Motorola H201 User Guide - Page 5

Getting started

Get Motorola H201 PDF manuals and user guides View all Motorola H201 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

1. Getting started WARNING Do not place your phone in the bathroom or other humid areas. Location When choosing a location for your new phone, here are some important guidelines you should consider: • Avoid sources of noise and heat, such as motors, fluorescent lighting, microwave ovens, heating appliances and direct sunlight. • Avoid areas of excessive dust, moisture, and low temperature. • Avoid other cordless telephones or personal computers. • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. HANDSET RANGE Optimal range is reached when there are no other electrical appliances working within the range area. Any obstruction between the base and handset will also reduce the range significantly. SIGNAL STRENGTH When out of range of the base, the screen shows SEARCHING.... If you are on a call, the line will disconnect. Move back within in range of the base. The handset will automatically re-connect to the base. Getting started Setting up IMPORTANT The base must be plugged into an electrical outlet at all times. Do not connect the telephone line cord into a power outlet until the handset is fully charged. Only use the power adapter and telephone line cord supplied with the product. WHICH POWER ADAPTER The power adapter with the smaller pin is for the base unit and the power adapter with the larger pin is for the charger unit (only for multi-handset packs). 1.1 Connecting the base 1. Plug the power adapter with the smaller round pin plug and telephone line cord into the base. The power adapter with the larger round pin is for the charger (only in multi-handset packs). 2. Plug the other end of the power adapter and telephone line cord into a power outlet. 3. Use only the provided power adapter. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
Getting started
5
1. Getting started
WARNING
Do not place your phone in the bathroom or other humid areas.
Location
When choosing a location for your new phone, here are some important
guidelines you should consider:
°
Avoid sources of noise and heat, such as motors, fluorescent lighting,
microwave ovens, heating appliances and direct sunlight.
°
Avoid areas of excessive dust, moisture, and low temperature.
°
Avoid other cordless telephones or personal computers.
°
Never install telephone wiring during a lightning storm.
°
Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
°
Never touch non-insulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
°
Use caution when installing or modifying telephone lines.
HANDSET RANGE
Optimal range is reached when there are no other electrical appliances
working within the range area. Any obstruction between the base and
handset will also reduce the range significantly.
SIGNAL STRENGTH
When out of range of the base, the screen shows
SEARCHING
....
If you are
on a call, the line will disconnect. Move back within in range of the base.
The handset will automatically re-connect to the base.
Setting up
IMPORTANT
The base must be plugged into an electrical outlet at all times. Do not
connect the telephone line cord into a power outlet until the handset is fully
charged. Only use the power adapter and telephone line cord supplied with
the product.
WHICH POWER ADAPTER
The power adapter with the smaller pin is for the base unit and the power
adapter with the larger pin is for the charger unit (only for multi-handset packs).
1.1
Connecting the base
1.
Plug the power adapter with the smaller round pin plug and telephone
line cord into the base. The power adapter with the larger round pin is
for the charger (only in multi-handset packs).
2.
Plug the other end of the power adapter and telephone line cord into a
power outlet.
3.
Use only the provided power adapter.