NEC LT154 User Manual - Page 24

Operation - projector lamp

Get NEC LT154 - MultiSync UXGA DLP Projector PDF manuals and user guides
UPC - 050927232534
View all NEC LT154 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

3. OPERATION Connecting the Power Cable and Turn on the Projector Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed. 1. Connect the supplied power cable to the projector. POWESRTATAUCPSCCESCSARD STAONN/D BY ADJAUUTSTO SOURCE CANCEL CANCEL ENTER SELECT MENU RGB C CARD USB VIDEO PC CONTROL S-VIDEO AUDIO AC IN Plug the supplied power cable in the wall outlet. The projector will go into its standby mode and the power indicator will glow orange. 2. Turn on and off the Projector OFF ON VIDEO S-VIDEO AUTO ADJ. RGB 1 RGB 2 PJ Power ON button MENU MEN SELECT LASER Indicator ENTER SOURCE AUATDOJUST PCACCCASRETSDASTPUOSWER PC CONTROL VIDEO S-VIDEO ONS/TAND BY Power ON/STAND BY button To turn on the projector: Only after you press the "On" button on the remote control ("ON/ STAND BY" button on the projector cabinet) will the power indicator turn to green and the projector become ready to use. NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the "Auto Start" feature. (See page E-38.) NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized. To turn off the projector: First press the "off" button on the remote control ("ON/STAND BY" button on the projector cabinet) for a minimum of two seconds. The power indicator will glow orange. After the projector turns off, the cooling fans keep operating for one minute. NOTE: Do not disconnect the power cable during this time. Then, unplug the power cable. The power indicator will go out. Status of indicator light: turn on High-Bright mode: stand by STATUS POWER ON/ STAND BY steady orange light flashing one minute STATUS POWER steady light STATUS POWER Eco mode: stand by STATUS POWER flashing green light steady green light ON/ STAND BY steady orange light flashing one minute steady light STATUS POWER STATUS POWER flashing green light (High-Bright mode) Status of indicator light: turn off ON STATUS POWER ON/ STAND BY steady green light (Eco mode) Press a minimum of two seconds. steady green light cooling down STATUS POWER stand by STATUS POWER change to flashing green light steady orange light E - 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
E
–
24
3. OPERATION
Connecting the Power Cable and Turn on the
Projector
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
1.
Connect the supplied power cable to the projector.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
STAND BY
SOURCE
AUTO
ADJUST
PC CARD
ACCESS
AC IN
C CARD
USB
PC CONTROL
VIDEO
S-VIDEO
RGB
AUDIO
Plug the supplied power cable in the wall outlet. The projector will
go into its standby mode and the power indicator will glow orange.
2.
Turn on and off the Projector
VIDEO
S-VIDEO
AUTO ADJ.
RGB 1
MENU
LASER
RGB 2
P
J
ON
OFF
Power ON button
M
E
N
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
STAND BY
SOURCE
AUTO
ADJUST
PC
CARD
ACCESS
PC CONTROL
VIDEO
S-VIDEO
Power ON/STAND BY button
Indicator
To turn on the projector:
Only after you press the “On” button on the remote control (“ON/
STAND BY” button on the projector cabinet) will the power indicator
turn to green and the projector become ready to use.
NOTE:
To turn the projector on by plugging in the power cable, use the
menu and enable the
“
Auto Start
”
feature. (See page E-38.)
NOTE:
Immediately after turning on the projector, screen flicker may occur.
This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
To turn off the projector:
First press the “off” button on the remote control (“ON/STAND BY”
button on the projector cabinet) for a minimum of two seconds. The
power indicator will glow orange. After the projector turns off, the
cooling fans keep operating for one minute.
NOTE:
Do not disconnect the power cable during this time. Then, unplug
the power cable. The power indicator will go out.
Status of indicator light: turn on
POWER
STATUS
POWER
STATUS
ON
/
STAND BY
POWER
STATUS
High-Bright mode:
stand by
steady orange light
flashing green light
steady green light
flashing one minute
steady light
Eco mode:
POWER
STATUS
POWER
STATUS
POWER
STATUS
ON
/
STAND BY
stand by
steady orange light
flashing green light
(High-Bright mode)
steady green light
(Eco mode)
flashing one minute
steady light
Status of indicator light: turn off
ON
/
STAND BY
POWER
STATUS
POWER
STATUS
POWER
STATUS
ON
steady green light
change to flashing
green light
steady orange light
cooling down
stand by
Press a minimum
of two seconds.