Netgear GS748Tv4 GS748Tv4 Hardware Installation Guide - Page 24

Step 4: Connecting Devices to the Switch

Get Netgear GS748Tv4 PDF manuals and user guides View all Netgear GS748Tv4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

GS748T Smart Switch Hardware Installation Guide Step 4: Connecting Devices to the Switch The following procedure describes how to connect PCs to the switch's RJ-45 ports. The GS748T contains Auto Uplink technology, which allows the attaching of devices using either straight-through or crossover cables. GS748T 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45T 46T 47T 48T Combo Ports SFP LED GREEN= 100/ 47F 49 1000Mbps Blink=ACT Reset Power LED Link/Act Mode Green=Link at 1000M Yellow=Link at 100/10M Blink=ACT 48F 50 Factory Default ` ` Figure 7. Connecting Devices to the Switch Connect each PC to an RJ-45 network port on the Switch front panel (Figure 7). Use Category 5 (Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector to make these connections. Note: Ethernet specifications limit the cable length between the switch and the attached device to 100m (328 ft.). 24 | Chapter 4: Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
24
|
Chapter 4:
Installation
GS748T Smart Switch Hardware Installation Guide
Step 4: Connecting Devices to the Switch
The following procedure describes how to connect PCs to the switch’s RJ-45 ports. The
GS748T contains Auto Uplink technology, which allows the attaching of devices using either
straight-through or crossover cables.
Figure 7. Connecting Devices to the Switch
Connect each PC to an RJ-45 network port on the Switch front panel (
Figure 7
). Use
Category 5 (Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector
to make these connections.
Note:
Ethernet specifications limit the cable length between the
switch and the attached device to 100m (328 ft.).
LED Link/Act Mode
Green=Link at 1000M
Yellow=Link at 100/10M
Blink=ACT
Power
Reset
Factory
Default
1
2
3
4
5
6
7
8
9
10
11
12
22
1
3
14
15
16
17
1
8
19
20
21
2
3
24
3
4
25
26
27
2
8
29
3
0
3
1
3
2
33
3
5
3
6
3
7
38
3
9
40
41
42
4
3
44
46T
45T
4
8
F
47F
50
49
Combo
Ports
G
S
74
8
T
SFP LED
GREEN=
100/
1000Mbps
Blink=ACT
4
8
T
47T
`
`