Netgear GSM7212P GSM5212P/GSM7212P/GSM7212F/GSM7224P Hardware Installation Gui - Page 7

Rear Panels, Table 1., LED Descriptions Continued

Get Netgear GSM7212P PDF manuals and user guides View all Netgear GSM7212P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

NETGEAR Managed Switch Table 1. LED Descriptions (Continued) LED PoE Description OFF: No PoE powered device (PD) connected Solid Green:The PoE powered device (PD) is connected and the port is supplying power successfully Solid Yellow: Indicates one of the following failures resulted in stopping power to that port: - Short circuit on PoE power circuit - PoE power demand exceeds power available - PoE current exceeds PD's classification - Out of proper voltage (44 ~ 57 VDC for af, 50~57 VDC for at) Link/ACT (RJ45 port) SPD (RJ45 port) PoE-PD SPD/Link/ACT (SFP port) OFF: No link is established on the port Solid Green: A valid link is established on the port Blinking Green: Packets transmission or reception is occurring on the port Note: On the GSM7212F, if a combo port media changes to fiber, the copper port LED will change to OFF status. OFF: No link is established on the port Solid Green: A valid 1000Mbps link is established on the port Solid Yellow: A valid 10/100Mbps link is established on the por. Note: On the GSM7212F, if a combo port media changes to fiber, the copper port LED will change to OFF status OFF: No PSE is connected or connected but has failed Solid Green: The PSE is connected and get 30W power from PSE successfully Solid Yellow: The PSE is connected and get 15.4W power from PSE successfully Note: only for GSM5212P port 1 and 2 Off: No SFP/SFP+ module link is established on the port Solid green: A valid 1000Mbps SFP+ module link is established on the port Blinking green: The port is transmitting or receiving packets at 1000Mbps Solid yellow: A valid 100Mbps SFP module link is established on the port Blinking yellow: Packet transmission or reception is occurring on the port at 100Mbps Note:If combo port media change to Copper, the SFP port LED will change to OFF status. Rear Panels The rear panels have a console port, a redundant power supply connector (only for GSM7212F, GSM7212P, and GSM7224P), and a standard AC power receptacle for the supplied power cord. Introduction 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Introduction
7
NETGEAR Managed Switch
Rear Panels
The rear panels have a console port, a redundant power supply connector (only for
GSM7212F, GSM7212P, and GSM7224P), and a standard AC power receptacle for the
supplied power cord.
PoE
OFF:
No PoE powered device (PD) connected
Solid Green:
The PoE powered device (PD) is connected and the port is supplying
power successfully
Solid Yellow:
Indicates one of the following failures resulted in stopping power to
that port:
- Short circuit on PoE power circuit
- PoE power demand exceeds power available
- PoE current exceeds PD's classification
- Out of proper voltage (44 ~ 57 VDC for af, 50~57 VDC for at)
Link/ACT
(RJ45 port)
OFF
: No link is established on the port
Solid Green:
A valid link is established on the port
Blinking Green:
Packets transmission or reception is occurring on the port
Note: On the GSM7212F, if a combo port media changes to fiber, the copper port
LED will change to OFF status.
SPD (RJ45 port)
OFF
: No link is established on the port
Solid Green:
A valid 1000Mbps link is established on the port
Solid Yellow:
A valid 10/100Mbps link is established on the por.
Note: On the GSM7212F, if a combo port media changes to fiber, the copper port
LED will change to OFF status
PoE-PD
OFF:
No PSE is connected or connected but has failed
Solid Green:
The PSE is connected and get 30W power from PSE successfully
Solid Yellow:
The PSE is connected and get 15.4W power from PSE successfully
Note: only for GSM5212P port 1 and 2
SPD/Link/ACT
(SFP port)
Off:
No SFP/SFP+ module link is established on the port
Solid green:
A valid 1000Mbps SFP+ module link is established on the port
Blinking green:
The port is transmitting or receiving packets at 1000Mbps
Solid yellow
: A valid 100Mbps SFP module link is established on the port
Blinking yellow:
Packet transmission or reception is occurring on the port at
100Mbps
Note:If combo port media change to Copper, the SFP port LED will change to OFF
status.
Table 1.
LED Descriptions (Continued)
LED
Description