Netgear RN204 Hardware Manual - Page 33

Power State, Boot Menu

Get Netgear RN204 PDF manuals and user guides View all Netgear RN204 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

ReadyNAS OS 6 Desktop Storage Systems Power State If the power supply is interrupted due to a power failure, the system returns to its last state when the power supply is restored: • If the system was powered on at the time of the power failure, the system powers on when the power supply is restored. • If the system was powered off at the time of the power failure, the system remains off when the power supply is restored. Boot Menu Use the boot menu to restart or troubleshoot your ReadyNAS storage system. Your storage system has the following boot modes: • Normal. Initiates a normal boot process, just like booting using the Power button. • Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a 10-minute time-out period begins. WARNING: The factory default reboot process resets the storage system to factory settings, erases all data, resets all defaults, and reformats the disk to X-RAID. - If you want to cancel the factory default process, power off the storage system before the 10-minute time-out ends. The system powers down safely without causing any data loss. - If you want to reset the system to factory default settings, do not power off your system. After the 10-minute time-out period, the factory default process begins. Tip: To start the factory default process immediately, press the Backup button during the 10-minute time-out period. • OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets some settings on your storage system, such as Internet protocol settings and the administrator password, to defaults. • Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a NETGEAR technical support representative instructs you to do so. • Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue data off a disk during a disaster recovery. NETGEAR ReadyNAS 202 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
NETGEAR ReadyNAS 202
33
ReadyNAS OS 6 Desktop Storage Systems
Power State
If the power supply is interrupted due to a power failure, the system returns to its last state
when the power supply is restored:
•
If the system was powered on at the time of the power failure, the system powers on
when the power supply is restored.
•
If the system was powered off at the time of the power failure, the system remains off
when the power supply is restored.
Boot Menu
Use the boot menu to restart or troubleshoot your ReadyNAS storage system. Your storage
system has the following boot modes:
•
Normal
. Initiates a normal boot process, just like booting using the Power button.
•
Factory default
. Initiates a short disk test that takes approximately 5 minutes. After the
disk test, a 10-minute time-out period begins.
WARNING:
The factory default reboot process resets the storage system to
factory settings, erases all data, resets all defaults, and reformats
the disk to X-RAID.
-
If you want to cancel the factory default process, power off the storage system before
the 10-minute time-out ends. The system powers down safely without causing any
data loss.
-
If you want to reset the system to factory default settings, do not power off your
system. After the 10-minute time-out period, the factory default process begins.
Tip:
To start the factory default process immediately, press the
Backup
button during the 10-minute time-out period.
•
OS reinstall
. Reinstalls the firmware from the internal flash to the disks. Use the OS
reinstall boot mode when the system crashes and corrupts some configuration files. OS
reinstall boot mode also resets some settings on your storage system, such as Internet
protocol settings and the administrator password, to defaults.
•
Tech support
. Boots into a low-level diagnostic mode. Use the tech support boot mode
only when a NETGEAR technical support representative instructs you to do so.
•
Volume read only
. Mounts a volume as read-only. Use this option when you are
attempting to rescue data off a disk during a disaster recovery.