Home » Netgear Manuals » Wireless » Netgear WAG302v1 » Manual Viewer

Netgear WAG302v1 WAG302v1 Reference Manual - Page 66

Enable SysLog, SysLog Server IP address, Apply, Refresh, Save

Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

ProSafe Dual Band Wireless Access Point WAG302 Reference Manual (802.11a/g) Figure 3-3 2. Enable SysLog - Enable this option if you have a SysLog server on your LAN. If enabled, you must enter the IP address of your SysLog server and the port number your SysLog server is configured to use. a. SysLog Server IP address -The access point will send all the SysLog to the specified IP address if SysLog option is enabled. Default: 0.0.0.0 b. Port - The port number configured in the SysLog server on your LAN. Default: 514 3. Click Apply to save your Syslog settings. The Activity Log Window displays the Access Point system activity. Click Refresh to update the display or click Save As to save the log contents into a file on your PC or to save the file to a disk drive. 3-4 Management v2.0, May 2006

Section	Page
NETGEAR ProSafe Dual Band Wireless Access Point WAG302 Reference Manual (802.11a/g)	1
About This Manual	13
Conventions, Formats and Scope	13
How to Use This Manual	14
How to Print this Manual	15
Chapter 1 Introduction	17
About the ProSafe 802.11a/g Dual Band Wireless Access Point WAG302	17
Key Features and Standards	18
Supported Standards and Conventions	18
Key Features	18
802.11a/g Standards-based Wireless Networking	20
Autosensing Ethernet Connections with Auto Uplink	20
Compatible and Related NETGEAR Products	21
System Requirements	21
What’s In the Box?	21
Hardware Description	22
Front Panel	22
Rear Panel	24
Chapter 2 Basic Installation and Configuration	25
Wireless Equipment Placement and Range Guidelines	25
Understanding WAG302 Wireless Security Options	26
Installing the WAG302 Wireless Access Point	27
Setting up the WAG302 Wireless Access Point	28
Configuring LAN and Wireless Access	28
Deploying the WAG302 Wireless Access Point	33
Verifying Wireless Connectivity	33
Logging In Using the Default IP Address	34
Setting Basic IP Options	35
Wireless Settings	38
Configuring 802.11a Wireless Settings	38
Configuring 802.11b/g Wireless Settings	39
Setting Up and Testing Basic Wireless Connectivity	41
Understanding Security Profiles	42
SSID and WEP/WPA Settings Setup Form	46
Configuring the RADIUS Server Settings	48
Setting up a Security Profile	50
Restricting Wireless Access by MAC Address	60
Chapter 3 Management	63
Remote Management	63
Using the Secure Telnet Interface	64
CLI Commands	65
Using Syslog and Activity Log Information	65
Viewing General Summary Information	67
Viewing Network Traffic Statistics	70
Viewing Available Wireless Station Statistics	71
Upgrading the Wireless Access Point Software	72
Configuration File Management	73
Saving and Retrieving the Configuration	74
Restoring the WAG302 to the Factory Default Settings	75
Changing the Administrator Password	75
Chapter 4 Advanced Configuration	77
IP Settings for Wireless Clients	77
Hotspot Settings	79
Configuring Advanced Wireless Settings	79
Enabling Wireless Bridging and Repeating	81
Configuring a WAG302 as a Point-to-Point Bridge	83
Configuring a Point-to-Multi-Point Wireless Bridge	84
Configuring the WAG302 as a Wireless Repeater	85
Chapter 5 Troubleshooting	89
No lights are lit on the wireless access point.	89
The Wireless LAN activity light does not light up.	90
The LAN light is not lit.	90
I cannot access the Internet or the LAN with a wireless capable computer.	90
I cannot connect to the WAG302 to configure it.	91
When I enter a URL or IP address I get a timeout error.	91
Using the Reset Button to Restore Factory Default Settings	92
Appendix A Default Settings and Technical Specifications	93
Factory Default Settings	93
Technical Specifications	95
Appendix B Related Documents	97
Appendix C Command Line Reference	99
Command Sets	99