Netgear WAG302v1 WAG302v1 Reference Manual - Page 89

Troubleshooting, No lights are lit on the wireless access point.

Get Netgear WAG302v1 - ProSafe Dual Band Wireless Access Point PDF manuals and user guides View all Netgear WAG302v1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Chapter 5 Troubleshooting This chapter provides information about troubleshooting your ProSafe 802.11a/g Dual Band Wireless Access Point WAG302. After each problem description, instructions are given to help you diagnose and solve the problem. For the common problems listed, go to the section indicated. • Is the WAG302 on? Go to "Installing the WAG302 Wireless Access Point" on page 2-3 • Have I connected the wireless access point correctly? Go to "Installing the WAG302 Wireless Access Point" on page 2-3. • I cannot remember the wireless access point's configuration password. Go to "Changing the Administrator Password" on page 3-13. Note: For up-to-date WAG302 installation details and troubleshooting guidance visit http://kbserver.netgear.com/products/WG302.asp. If you have trouble setting up your WAG302, check the tips below. No lights are lit on the wireless access point. It takes a few seconds for the power indicator to light up. Wait a minute and check the power light status on the access point. If the access point has no power. • Make sure the power cord is connected to the access point. • Make sure the power adapter is connected to a functioning power outlet. If it is in a power strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it is not a switched outlet. • Make sure you are using the correct NETGEAR power adapter supplied with your access point. 5-1 v2.0, May 2006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
5-1
v2.0, May 2006
Chapter 5
Troubleshooting
This chapter provides information about troubleshooting your ProSafe 802.11a/g Dual Band
Wireless Access Point WAG302. After each problem description, instructions are given to help
you diagnose and solve the problem. For the common problems listed, go to the section indicated.
•
Is the WAG302 on?
Go to
“Installing the WAG302 Wireless Access Point” on page 2-3
•
Have I connected the wireless access point correctly?
Go to
“Installing the WAG302 Wireless Access Point” on page 2-3
.
•
I cannot remember the wireless access point’s configuration password.
Go to
“Changing the Administrator Password” on page 3-13
.
If you have trouble setting up your WAG302, check the tips below.
No lights are lit on the wireless access point.
It takes a few seconds for the power indicator to light up. Wait a minute and check the power light
status on the access point.
If the access point has no power.
•
Make sure the power cord is connected to the access point.
•
Make sure the power adapter is connected to a functioning power outlet. If it is in a power
strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it
is not a switched outlet.
•
Make sure you are using the correct NETGEAR power adapter supplied with your access
point.
Note:
For up-to-date WAG302 installation details and troubleshooting guidance visit
.