Home » Netgear Manuals » Wireless » Netgear WG602v2 » Manual Viewer

Netgear WG602v2 WG602v2 User Manual - Page 3

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice - installation guide

Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice NETGEAR 54 Mbps Wireless Access Point WG602 v2 Tested to Comply with FCC Standards FOR HOME OR OFFICE USE Warning! To comply with the FCC's exposure requirements you must maintain a distance of at least 1 cm from the antenna of this device while it is in use. This device should not be co-located with other transmitters. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. RF Exposure Requirements WARNING! To ensure compliance with FCC RF exposure requirements, the antenna used for this device must be installed to provide a separation distance of at least 20 cm (8 in) from all persons and must not be co-located or operating in conjunction with any other antenna or radio transmitter. Installers and end-users must follow the installation instructions provided in this user guide. 3 M-10181-03

Section	Page
Trademarks	2
Statement of Conditions	2
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice	3
Canadian Department of Communications Compliance Statement	4
CE Declaration of Conformity	5
Contents	7
Chapter 1 About This Manual	13
Audience, Scope, Conventions	13
How to Use this Manual	14
How to Print this Manual	15
Chapter 2 Introduction	17
About the 54 Mbps Wireless Access Point WG602 v2	17
Support for Standards	17
Key Features	18
802.11g Standards-based Wireless Networking	18
Autosensing Ethernet Connections with Auto Uplink	19
Compatible and Related NETGEAR Products	19
System Requirements	19
What’s In the Box?	20
Hardware Description	21
WG602 v2 Wireless Access Point Front Panel	21
WG602 v2 Wireless Access Point Rear Panel	22
Power Socket	22
Reset and Restore to Factory Defaults Button	22
RJ-45 Ethernet Port	22
Detachable Antenna	22
Chapter 3 Basic Installation and Configuration	24
Observing Placement and Range Guidelines	24
Default Factory Settings	25
Understanding WG602 v2 Wireless Security Options	26
Installing the 54 Mbps Wireless Access Point WG602 v2	27
Two Ways to Log In to the WG602 v2	29
How to Log in Using the Default IP Address of the WG602 v2	30
How to Log In to the WG602 v2 Using Its Default NetBIOS Name	31
Using the Basic IP Settings Options	33
Understanding the Basic Wireless Settings	34
Understanding Wireless Security Options	36
Information to Gather Before Changing Basic Wireless Settings	37
How to Configure WEP Wireless Security	38
How to Configure WPA-PSK Wireless Security	39
How to Restrict Wireless Access by MAC Address	40
Chapter 4 Management	43
Viewing General Information	43
Viewing a List of Attached Devices	45
Upgrading the Wireless Access Point Software	45
Rebooting and Resetting Factory Default Options	47
Restoring the WG602 v2 to the Factory Default Settings	47
Using the Reset Button to Reboot or Restore Factory Defaults	47
Changing the Administrator Password	48
Chapter 5 Advanced Configuration	49
Configuring Wireless Bridge or Repeater Links	49
How to Select the Wireless Bridging Access Point Mode	50
How to Configure a WG602 v2 as a Point-to-Point Bridge	51
How to Configure Wireless Multi-Point Bridging	52
How to Configure a WG602 v2 as a Repeater	54
Understanding Advanced Wireless Settings	55
Chapter 6 Troubleshooting	57
Troubleshooting	57
No lights are lit on the access point.	57
The Ethernet LAN light is not lit.	57
The Wireless LAN activity light is not lit.	58
I cannot configure the wireless access point from a browser.	58
I cannot access the Internet or the LAN with a wireless capable computer.	58
When I enter a URL or IP address I get a timeout error.	59
Using the Reset Button to Restore Factory Default Settings	59
Appendix A Specifications	61
Specifications for the WG602 v2	61
Appendix B Wireless Networking Basics	63
Wireless Networking Overview	63
Infrastructure Mode	63
Ad Hoc Mode (Peer-to-Peer Workgroup)	64
Network Name: Extended Service Set Identification (ESSID)	64
Wireless Channels	64
WEP Wireless Security	66
WEP Authentication	66
WEP Open System Authentication	67
WEP Shared Key Authentication	68
Key Size and Configuration	69
How to Use WEP Parameters	70
WPA Wireless Security	70
How Does WPA Compare to WEP?	71
How Does WPA Compare to IEEE 802.11i?	72
What are the Key Features of WPA Security?	72
WPA Authentication: Enterprise-level User Authentication via 802.1x/EAP and RADIUS	74
WPA Data Encryption Key Management	76
Temporal Key Integrity Protocol (TKIP)	77
Michael	77
AES Support	77
Is WPA Perfect?	78
Product Support for WPA	78
Supporting a Mixture of WPA and WEP Wireless Clients	78
Changes to Wireless Access Points	78
Changes to Wireless Network Adapters	79
Changes to Wireless Client Programs	80
Appendix C Network, Routing, Firewall, and Cabling Basics	81
Basic Router Concepts	81
What is a Router?	81
IP Addresses and the Internet	82
Netmask	84
Subnet Addressing	84
Private IP Addresses	87
Single IP Address Operation Using NAT	87
IP Configuration by DHCP	88
Domain Name Server	89
Routing Protocols	89
RIP	89
MAC Addresses and ARP	90
Internet Security and Firewalls	90
What is a Firewall?	91
Stateful Packet Inspection	91
Denial of Service Attack	91
Ethernet Cabling	91
Category 5 Cable Quality	92
Inside Twisted Pair Cables	93
Uplink Switches, Crossover Cables, and MDI/MDIX Switching	94
Appendix D Preparing Your PCs for Network Access	97
Preparing Your Computers for TCP/IP Networking	97
Configuring Windows 98 and Me for TCP/IP Networking	98
Installing or Verifying Windows Networking Components	98
Enabling DHCP to Automatically Configure TCP/IP Settings	99
DHCP Configuration of TCP/IP in Windows 98 and Me	100
Selecting the Windows Internet Access Method	101
Verifying TCP/IP Properties for Windows 98 or Me	101
Configuring Windows 2000 or XP for TCP/IP Networking	102
Installing or Verifying Windows Networking Components	102
DHCP Configuration of TCP/IP in Windows XP	103
DHCP Configuration of TCP/IP in Windows 2000	105
Verifying TCP/IP Properties for Windows XP or 2000	107
Glossary	109
Numeric	109
A	110
B	110
C	111
D	111
E	112
G	112
I	112
L	114
M	114
N	115
P	116
Q	117
R	117
S	117
T	118
U	118
W	118

Match case Limit results 1 per page

M-10181-03

Federal Communications Commission (FCC) Compliance Notice:

Radio Frequency Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired

operation.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

•

Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Requirements

WARNING!

To ensure compliance with FCC RF exposure requirements, the antenna used for this device

must be installed to provide a separation distance of at least 20 cm (8 in) from all persons and must not be

co-located or operating in conjunction with any other antenna or radio transmitter. Installers and end-users

must follow the installation instructions provided in this user guide.

FOR HOME OR OFFICE USE

Tested to Comply

with FCC Standards

Warning!

To comply with the FCC’s

exposure requirements you must

maintain a distance of at least 1

cm from the antenna of this

device while it is in use. This

device should not be co-located

with other transmitters.

NETGEAR 54 Mbps Wireless Access Point WG602 v2