NordicTrack C 850s Treadmill English Manual - Page 15

May Become Damaged When You Turn

Get NordicTrack C 850s Treadmill PDF manuals and user guides View all NordicTrack C 850s Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

12. With the help of a second person, hold the console assembly (I) near the Handrails (86) (only one side is shown). Connect the ground wire (J) from the console assembly (I) to the Console Ground Wire (58) on the Pulse Crossbar (93). Next, insert the Upright Wire (81) through the two indicated looped ties (K) on the console assembly. See the inset drawing. Connect the Upright Wire (81) to the console wire (L). The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. Then, remove the wire tie (A) from the Upright Wire. 12 K I L 81 86 93 A J 58 L 81 13. Set the console assembly (I) on the brackets on the Handrails (86). Make sure not to pinch any wires. Attach the console assembly (I) to the brackets on the Handrails (86) with the four 5/16" x 3/4" Screws (4) that you removed in step 9 and four 5/16" Star Washers (11). Do not fully tighten the Screws yet. Insert the excess Upright Wire (81) into the console assembly (I) . Pull the two ties (K) tight against the Upright Wire and cut off the ends of the ties. 13 86 K 81 11 4 I 86 11 4 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
15
12.
With the help of a second person, hold the con-
sole assembly (I) near the Handrails (86) (only
one side is shown).
Connect the ground wire (J) from the console
assembly (I) to the Console Ground Wire (58) on
the Pulse Crossbar (93).
Next, insert the Upright Wire (81) through the
two indicated looped ties (K) on the console
assembly.
See the inset drawing.
Connect the Upright
Wire (81) to the console wire (L).
The connec-
tors should slide together easily and snap
into place.
If they do not, turn one connector
and try again.
IF YOU DO NOT CONNECT THE
CONNECTORS PROPERLY, THE CONSOLE
MAY BECOME DAMAGED WHEN YOU TURN
ON THE POWER.
Then, remove the wire tie (A)
from the Upright Wire.
12
81
L
L
A
81
K
86
58
I
93
13.
Set the console assembly (I) on the brackets on
the Handrails (86).
Make sure not to pinch any
wires.
Attach the console assembly (I) to the brackets
on the Handrails (86) with the four 5/16" x 3/4"
Screws (4) that you removed in step 9 and four
5/16" Star Washers (11).
Do not fully tighten
the Screws yet.
Insert the excess Upright Wire (81) into the
console assembly (I) . Pull the two ties (K) tight
against the Upright Wire and cut off the ends of
the ties.
13
86
4
4
81
K
86
11
11
I
J