NordicTrack C 850s Treadmill English Manual - Page 30

Unplug The Power Cord.

Get NordicTrack C 850s Treadmill PDF manuals and user guides View all NordicTrack C 850s Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

SYMPTOM: The incline of the treadmill does not change correctly a. Hold down the Stop button, insert the key into the console, and then release the Stop button. Next, press the Stop button and then press the Incline increase or decrease button. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system. If the incline system does not begin calibrating, press the Stop button again, and then press the Incline increase or decrease button again. When the incline system is calibrated, remove the key from the console. SYMPTOM: The walking belt slows when walked on a. Use only a surge suppressor that meets all of the specifications described on page 19. b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened. c. Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform unless instructed to do so by an authorized service representative. Such substances may deteriorate the walking belt and cause excessive wear. If you suspect that the walking belt needs more lubricant, see the front cover of this manual. d. If the walking belt still slows when walked on, see the front cover of this manual. SYMPTOM: The walking belt is off-center or slips when walked on a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered. a b 2-3 in. Idler Roller Screws 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
30
SYMPTOM: The incline of the treadmill does not
change correctly
a.
Hold down the Stop button, insert the key into the
console, and then release the Stop button. Next,
press the Stop button and then press the Incline
increase or decrease button. The treadmill will
automatically rise to the maximum incline level and
then return to the minimum level. This will recalibrate
the incline system. If the incline system does not
begin calibrating, press the Stop button again, and
then press the Incline increase or decrease but-
ton again. When the incline system is calibrated,
remove the key from the console.
SYMPTOM: The walking belt slows when walked on
a.
Use only a surge suppressor that meets all of the
speci
fi
cations described on page 19.
b.
If the walking belt is overtightened, treadmill per-
formance may decrease and the walking belt may
become damaged. Remove the key and
UNPLUG
THE POWER CORD.
Using the hex key, turn both
idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
c.
Your treadmill features a walking belt coated with
high-performance lubricant.
IMPORTANT: Never
apply silicone spray or other substances to
the walking belt or the walking platform unless
instructed to do so by an authorized service
representative. Such substances may deterio-
rate the walking belt and cause excessive wear.
If you suspect that the walking belt needs more
lubricant, see the front cover of this manual.
d.
If the walking belt still slows when walked on, see
the front cover of this manual.
SYMPTOM: The walking belt is off-center or slips
when walked on
a.
If the walking belt is off-center,
fi
rst remove the
key and
UNPLUG THE POWER CORD.
If the
walking belt has shifted to the left,
use the hex
key to turn the left idler roller screw clockwise 1/2
of a turn;
if the walking belt has shifted to the
right,
turn the left idler roller screw counterclock-
wise 1/2 of a turn. Be careful not to overtighten the
walking belt.
Then, plug in the power cord, insert
the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
Idler Roller Screws
2–3 in.
b
a