Oki MICROLINE 1120 Users Guide 2 - Page 56

Buffer Print, Invalid, Enable, 200 bps, Ready on Power UP, 2 sec

Get Oki MICROLINE 1120 PDF manuals and user guides View all Oki MICROLINE 1120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

MENU Parallel I/F Serial I/F Item I-Prime Auto Feed XT Bi-Direction Parity Serial Data 7/8 Bits Protocol Diagnostic Test Baud Rate DTR Signal Busy Time Function Setting Set I-Prime signal control Invalid of the Centronics interface. Buffer Print Buffer Clear Set whether to enable or disable Auto Feed XT signal of the Centronics interface. (EPSON emulation only) Valid Invalid Set whether to enable or disable Two-way communication of the Centronics interface. Enable Disable Set parity. None Odd Even Ignore Set serial data length. 8 bit 7 bit Set protocols. DTR X-ON/X-OFF DTR & X-ON/X-OFF Set/Cancel loop testing of No the serial interface. Yes Set the transmission speed of the serial interface. 9,600 bps 4,800 bps 2,400 bps 1,200 bps 600 bps 300 bps 19,200 bps Set whether to switch the DTR signal of the serial interface by Select/ Deselect or hold it after power-on. Ready on Power UP Ready on Select Set the minimum time it 0.2 sec takes to switch from a busy 1.0 sec state to a ready state. ML1120/ML1190 User's Guide - Operating instructions > 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
ML1120/ML1190 User’s Guide - Operating instructions > 56
MENU
ITEM
FUNCTION
SETTING
Parallel I/F
I-Prime
Set I-Prime signal control
of the Centronics interface.
Invalid
Buffer Print
Buffer Clear
Auto Feed XT
Set whether to enable
or disable Auto Feed XT
signal of the Centronics
interface.
(EPSON emulation only)
Valid
Invalid
Bi-Direction
Set whether to enable
or disable Two-way
communication of the
Centronics interface.
Enable
Disable
Serial I/F
Parity
Set parity.
None
Odd
Even
Ignore
Serial Data 7/8
Bits
Set serial data length.
8 bit
7 bit
Protocol
Set protocols.
DTR
X-ON/X-OFF
DTR & X-ON/X-OFF
Diagnostic Test
Set/Cancel loop testing of
the serial interface.
No
Yes
Baud Rate
Set the transmission speed
of the serial interface.
9,600 bps
4,800 bps
2,400 bps
1,200 bps
600 bps
300 bps
19,200 bps
DTR Signal
Set whether to switch
the DTR signal of the
serial interface by Select/
Deselect or hold it after
power-on.
Ready on Power UP
Ready on Select
Busy Time
Set the minimum time it
takes to switch from a busy
state to a ready state.
0.2 sec
1.0 sec