Oki MICROLINE 1120 Users Guide 2 - Page 64

Set the Power Switch to OFF.

Get Oki MICROLINE 1120 PDF manuals and user guides View all Oki MICROLINE 1120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

MENU Serial I/F Item Parity Serial Data 7/8 Bits Protocol Diagnostic Test Baud Rate DTR Signal Busy Time Function Setting Set parity. None Odd Even Ignore Set serial data length. 8 bit 7 bit Set protocols. DTR X-ON/X-OFF DTR & X-ON/X-OFF Set/Cancel loop testing of No the serial interface. Yes Set the transmission speed of the serial interface. 9,600 bps 4,800 bps 2,400 bps 1,200 bps 600 bps 300 bps 19,200 bps Set whether to switch the DTR signal of the serial interface by Select/ Deselect or hold it after power-on. Ready on Power UP Ready on Select Set the minimum time it 0.2 sec takes to switch from a busy 1.0 sec state to a ready state. Initialising menu settings To restore the menu settings to their initial values, carry out the steps below. NOTE The values adjusted by the Adjustment menus are not initialised by the following procedure. 1. Set the Power Switch to OFF. 2. Press and hold down the SEL and LF/FF buttons together and then set the Power Switch to ON. ML1120/ML1190 User's Guide - Operating instructions > 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
ML1120/ML1190 User’s Guide - Operating instructions > 64
I
NITIALISING
MENU
SETTINGS
To restore the menu settings to their initial values, carry out the steps
below.
NOTE
The values adjusted by the Adjustment menus are not initialised by
the following procedure.
1.
Set the Power Switch to OFF.
2.
Press and hold down the SEL and LF/FF buttons together and
then set the Power Switch to ON.
MENU
ITEM
FUNCTION
SETTING
Serial I/F
Parity
Set parity.
None
Odd
Even
Ignore
Serial Data 7/8
Bits
Set serial data length.
8 bit
7 bit
Protocol
Set protocols.
DTR
X-ON/X-OFF
DTR & X-ON/X-OFF
Diagnostic Test
Set/Cancel loop testing of
the serial interface.
No
Yes
Baud Rate
Set the transmission
speed of the serial
interface.
9,600 bps
4,800 bps
2,400 bps
1,200 bps
600 bps
300 bps
19,200 bps
DTR Signal
Set whether to switch
the DTR signal of the
serial interface by Select/
Deselect or hold it after
power-on.
Ready on Power UP
Ready on Select
Busy Time
Set the minimum time it
takes to switch from a busy
state to a ready state.
0.2 sec
1.0 sec