Olympus VP-1 VP-1 User's Manual - Simplified Edition (English) - Page 33

Troubleshooting

Get Olympus VP-1 - Data Projector - DLP PDF manuals and user guides
UPC - 050332147072
View all Olympus VP-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Troubleshooting Check the following matters before requesting servicing. Problem No power Check Reference Page * Has the power plug become disconnected from the E-16(S) outlet? * Is the lamp cover properly attached? E-31, 38(S) * Has the internal temperature become high? When the E-31, 32(S) internal temperature becomes very high, to protect the unit the power will not switch on. * Has the lamp timer exceeded 1100 hours? The power E-32(S) will no longer switch on once the timer has exceeded 1100 hours. No video * Has the connected input been selected? E-20(S) * Is the cable of the input connector properly connected? E-12 - 15(S) * If there is connection to a personal computer, is a E-20(C) signal being output from the personal computer? * Has a signal that is higher than the supported fre- E-70(C) quency of the projector been input? * Check that the image adjustment brightness and con- E-25(S), 46(C) trast are not set to minimum. * Has the lamp burned out? E-31(S) * Is the STATUS indicator blinking? E-31(S) * When a monochrome video signal cannot be dis- E-20(S) played properly, set the input selection to "YCbCr". Distorted video * Is the projector installed properly? * Is the keystone adjustment properly adjusted? E-18(S) E-26(S), 53(C) Blurred video * Is the lens properly focussed? E-19(S) * Are the projection screen and the projector installed E-10, 11(S) at the proper distance? * Has the projection distance exceeded the focussing E-10, 11(S) range? * Is there condensation on the lens and other parts? - When the projector has been stored in a cold location and the power is switched on in a warm location, there may be condensation on the lens and other internal optical parts. Should this occur, wait several minutes until the condensation disappears. Image position is shifted * Is the input signal being supported for resolution and and doesn't display prop- frequency? Check the resolution of your personal com- erly puter. E-70(C) Image is broken * When the image is broken in the horizontal or vertical E-22(S), 51(C) direction, or the image does not fill the entire screen, select a suitable aspect ratio. Overall color of image is * When a component signal is being input, the color strange space setting is different. Perform the color space setting. E-33 E-50(C)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
E-33
Troubleshooting
Check the following matters before requesting servicing.
*
Has the power plug become disconnected from the
outlet?
*
Is the lamp cover properly attached?
*
Has the internal temperature become high? When the
internal temperature becomes very high, to protect
the unit the power will not switch on.
*
Has the lamp timer exceeded 1100 hours? The power
will no longer switch on once the timer has exceeded
1100 hours.
*
Has the connected input been selected?
*
Is the cable of the input connector properly connected?
*
If there is connection to a personal computer, is a
signal being output from the personal computer?
*
Has a signal that is higher than the supported fre-
quency of the projector been input?
*
Check that the image adjustment brightness and con-
trast are not set to minimum.
*
Has the lamp burned out?
*
Is the STATUS indicator blinking?
*
When a monochrome video signal cannot be dis-
played properly, set the input selection to "YCbCr".
*
Is the projector installed properly?
*
Is the keystone adjustment properly adjusted?
*
Is the lens properly focussed?
*
Are the projection screen and the projector installed
at the proper distance?
*
Has the projection distance exceeded the focussing
range?
*
Is there condensation on the lens and other parts?
When the projector has been stored in a cold location
and the power is switched on in a warm location, there
may be condensation on the lens and other internal
optical parts. Should this occur, wait several minutes
until the condensation disappears.
*
Is the input signal being supported for resolution and
frequency? Check the resolution of your personal com-
puter.
*
When the image is broken in the horizontal or vertical
direction, or the image does not fill the entire screen,
select a suitable aspect ratio.
*
When a component signal is being input, the color
space setting is different. Perform the color space
setting.
No power
No video
Distorted video
Blurred video
Image position is shifted
and doesn
’
t display prop-
erly
Image is broken
Overall color of image is
strange
Problem
Check
Reference
Page
E-16(S)
E-31, 38(S)
E-31, 32(S)
E-32(S)
E-20(S)
E-12
–
15(S)
E-20(C)
E-70(C)
E-25(S), 46(C)
E-31(S)
E-31(S)
E-20(S)
E-18(S)
E-26(S), 53(C)
E-19(S)
E-10, 11(S)
E-10, 11(S)
–
E-70(C)
E-22(S), 51(C)
E-50(C)