Onkyo PR-SC885 Owner Manual - Page 77

Using the Sleep Timer, Using Headphones, Displaying Source Information, To cancel the sleep timer

Get Onkyo PR-SC885 PDF manuals and user guides View all Onkyo PR-SC885 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Common Functions-Continued Using the Sleep Timer With the sleep timer, you can set the AV controller so that it turns off automatically after a specified period. SLEEP Press the remote controller's [SLEEP] button repeatedly to select the required sleep time. You can set the sleep time from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 sec- onds, then the previous display reap- pears. SLEEP indicator To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV controller's PHONES jack. Displaying Source Information You can display various information about the current input source as follows. Remote controller DISPLAY Press the [DISPLAY] button repeatedly to cycle through the available information. AV controller DISPLAY The following information can typically be displayed: Input source Listening mode Signal format* Sampling frequency * If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format and the number of channels is displayed. For some digital input signals, including multichannel PCM, the signal format, number of channels, and sampling frequency is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Notes: • Always turn down the volume before connecting your headphones. • While the headphones plug is inserted in the PHONES jack, the speakers are turned off and the Headphone indicator lights up. • When you connect a pair of headphones, the listening mode is set to Stereo, unless it was already set to Pure Audio, Mono, Stereo, or Direct, in which case it stays the same. 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
77
Common Functions
—Continued
With the sleep timer, you can set the AV controller so
that it turns off automatically after a specified period.
To cancel the sleep timer,
press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
To check the remaining sleep time,
press the [SLEEP]
button. Note that if you press the [SLEEP] button while
the sleep time is being displayed, you’ll shorten the sleep
time by 10 minutes.
For private listening, you can connect a pair of stereo
headphones (1/4-inch phone plug) to the AV controller’s
PHONES jack.
Notes:
•
Always turn down the volume before connecting your
headphones.
•
While the headphones plug is inserted in the PHONES
jack, the speakers are turned off and the Headphone
indicator lights up.
•
When you connect a pair of headphones, the listening
mode is set to Stereo, unless it was already set to Pure
Audio, Mono, Stereo, or Direct, in which case it stays
the same.
You can display various information about the current
input source as follows.
The following information can typically be displayed:
*
If the input signal is analog, no format information is
displayed. If the input signal is PCM, the sampling
frequency is displayed. If the input signal is digital but
not PCM, the signal format and the number of chan-
nels is displayed. For some digital input signals,
including multichannel PCM, the signal format, num-
ber of channels, and sampling frequency is displayed.
Information is displayed for about 3 seconds, then the
previous display reappears.
Using the Sleep Timer
Press the remote controller’s
[SLEEP] button repeatedly to
select the required sleep time.
You can set the sleep time from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set, as shown. The specified sleep time
appears on the display for about 5 sec-
onds, then the previous display reap-
pears.
Using Headphones
SLEEP
SLEEP indicator
Displaying Source Information
Press the [DISPLAY] button
repeatedly to cycle through the
available information.
DISPLAY
DISPLAY
Remote
controller
AV controller
Input source
Listening
mode
Signal format*
Sampling
frequency