Onkyo TX-NR636 User Manual - Page 37

Network, Off Wired: Wired LAN connection - specifications

Get Onkyo TX-NR636 PDF manuals and user guides View all Onkyo TX-NR636 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Network Make the network setting. • When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the setting automatically. ("Enable" is set by default) To assign fixed IP addresses to each components, you must set "DHCP" to "Disable" and assign an address to this unit in "IP Address" as well as set information related to your LAN, such as Subnet Mask and Gateway. Setting item Network Standby Wi-Fi Wi-Fi Setup Wi-Fi Status MAC Address Default Value Off Off (Wired) - - - Setting Details You can turn on the power of the unit via network using an application such as Onkyo Remote. "On": Use this function "Off": Do not use this function • When "Network Standby" is used, the power consumption increases even when the unit is on standby. However, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only the essential circuit is operating. Connect the unit to network via wireless LAN router. "On": Wireless LAN connection "Off (Wired)": Wired LAN connection You can configure wireless LAN settings by pressing ENTER when "Start" is displayed. The information of the connected access point will be displayed. "SSID": SSID of the connected access point. "Security": Security method of the connected access point. "Signal": Signal strength of the connected access point. "Status": Status of the connected access point. This is the MAC address of the AV receiver. This value is specific to the component and cannot be changed. Advanced Settings Setting item DHCP IP Address Subnet Mask Gateway DNS Server Proxy URL Proxy Port Network Check Default Value Enable - - - - - - - Setting Details "Enable": Auto configuration by DHCP "Disable": Manual configuration without DHCP • If selecting "Disable", you must set "IP Address", "Subnet Mask", "Gateway", and "DNS Server" manually. Displays/Sets the IP address. Displays/Sets the subnet mask. Displays/Sets the gateway. Displays/Sets the primary DNS server. Displays/Sets the proxy server URL. Displays/Sets the proxy server port number when you enter "Proxy URL". You can check the network connection. Press ENTER when "Start" is displayed. • Wait for a while if "Network" is not shown on the screen. It will appear when the network function is started up. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Advanced Settings
37
Network
Make the network setting.
•
When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the
setting automatically. ("Enable" is set by default) To assign fixed IP addresses to each
components, you must set "DHCP" to "Disable" and assign an address to this unit in
"IP Address" as well as set information related to your LAN, such as Subnet Mask and
Gateway.
Setting item
Default Value
Setting Details
Network Standby
Off
You can turn on the power of the unit via
network using an application such as Onkyo
Remote.
"On": Use this function
"Off": Do not use this function
•
When "Network Standby" is used, the power
consumption increases even when the unit
is on standby. However, the increase in
power consumption is kept to a minimum
by automatically entering the HYBRID
STANDBY mode, where only the essential
circuit is operating.
Wi-Fi
Off (Wired)
Connect the unit to network via wireless LAN
router.
"On": Wireless LAN connection
"Off (Wired)": Wired LAN connection
Wi-Fi Setup
–
You can configure wireless LAN settings by
pressing ENTER when "Start" is displayed.
Wi-Fi Status
–
The information of the connected access point
will be displayed.
"SSID": SSID of the connected access point.
"Security": Security method of the connected
access point.
"Signal": Signal strength of the connected
access point.
"Status": Status of the connected access point.
MAC Address
–
This is the MAC address of the AV receiver.
This value is specific to the component and
cannot be changed.
Setting item
Default Value
Setting Details
DHCP
Enable
"Enable": Auto configuration by DHCP
"Disable": Manual configuration without DHCP
•
If selecting "Disable", you must set "IP
Address", "Subnet Mask", "Gateway", and
"DNS Server" manually.
IP Address
–
Displays/Sets the IP address.
Subnet Mask
–
Displays/Sets the subnet mask.
Gateway
–
Displays/Sets the gateway.
DNS Server
–
Displays/Sets the primary DNS server.
Proxy URL
–
Displays/Sets the proxy server URL.
Proxy Port
–
Displays/Sets the proxy server port number
when you enter "Proxy URL".
Network Check
–
You can check the network connection.
Press ENTER when "Start" is displayed.
•
Wait for a while if "Network" is not shown on the screen. It will appear when the network function is
started up.