Onkyo TX-NR901 Owner Manual - Page 48

Remote Setup

Get Onkyo TX-NR901 PDF manuals and user guides View all Onkyo TX-NR901 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

59/3@&OCPPL 1BHF  8FEOFTEBZ 0DUPCFS Basic Setup-Continued Remote Setup Specifying the Location of an IR Receiver This section explains how to specify the location when using a commercially available IR receiver. 1 Press the scroll wheel, and then press the [SETUP] button. The main menu appears onscreen. 2 ENTER Use the Up/Down [ ]/[ ] buttons to select "0. Hardware Setup," and then press the [ENTER] button. The Hardware Setup menu appears. Note: • This procedure can also be performed by using the TX-NR901's [SETUP] button buttons, and [ENTER] button. Changing the TX-NR901's Remote Control ID This section explains how to change the TX-NR901's remote control ID. You may need to change this if the TX-NR901's remote controller interferes with other Onkyo components located in the same room. Note: If you change the TX-NR901's remote control ID, be sure to select the same ID on the remote controller (page 49). The default ID for both the TX-NR901 and remote controller is 1. 1 Press the scroll wheel, and then press the [SETUP] button. The main menu appears onscreen. ENTER 3 ENTER ENTER Use the Up/Down [ ]/[ ] buttons to select "3. Remote Setup," and then press the [ENTER] button. The Remote Setup menu appears. 0-3.Remote Setup a.Position b.Remote ID :Main :1 2 ENTER ENTER Use the Up/Down [ ]/[ ] buttons to select "0. Hardware Setup," and then press the [ENTER] button. The Hardware Setup menu appears. 4 ENTER 5 Quit:[SETUP] Use the Up/Down [ ]/[ ] buttons to select "a. Position," and then use the Left/Right [ ]/[ ] buttons to select: Main: Select if the IR receiver is located in the main room. Zone 2: Select if the IR receiver is located in, and will be used to control Zone 2. Press the [SETUP] button. The setup menu closes. 3 ENTER ENTER 4 ENTER Use the Up/Down [ ]/[ ] buttons to select "3. Remote Setup," and then press the [ENTER] button. The Remote Setup menu appears. Use the Up/Down [ ]/[ ] buttons to select "b. Remote ID," and then use the Left/Right [ ]/[ ] buttons to select an ID: 1 (default), 2, or 3. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
48
Basic Setup
—Continued
Specifying the Location of an IR Receiver
This section explains how to specify the location when
using a commercially available IR receiver.
Note:
•
This procedure can also be performed by using the
TX-NR901’s [SETUP] button, [
]/[
]/[
]/[
]
buttons, and [ENTER] button.
Changing the TX-NR901’s Remote Control
ID
This section explains how to change the TX-NR901’s
remote control ID. You may need to change this if the
TX-NR901’s remote controller interferes with other
Onkyo components located in the same room.
Note:
If you change the TX-NR901’s remote control ID, be
sure to select the same ID on the remote controller
(page 49). The default ID for both the TX-NR901 and
remote controller is 1.
Remote Setup
1
Press the scroll wheel, and then
press the [SETUP] button.
The main menu appears onscreen.
2
Use the Up/Down [
]/[
] but-
tons to select “0. Hardware
Setup,” and then press the
[ENTER] button.
The Hardware Setup menu appears.
3
Use the Up/Down [
]/[
] but-
tons to select “3. Remote Setup,”
and then press the [ENTER] but-
ton.
The Remote Setup menu appears.
4
Use the Up/Down [
]/[
] but-
tons to select “a. Position,” and
then use the Left/Right [
]/[
]
buttons to select:
Main:
Select if the IR receiver is
located in the main room.
Zone 2:
Select if the IR receiver is
located in, and will be used to
control Zone 2.
5
Press the [SETUP] button.
The setup menu closes.
ENTER
ENTER
ENTER
ENTER
0-3.Remote Setup
a.Position
:Main
b.Remote ID
:1
Quit:[SETUP]
ENTER
1
Press the scroll wheel, and then
press the [SETUP] button.
The main menu appears onscreen.
2
Use the Up/Down [
]/[
] but-
tons to select “0. Hardware
Setup,” and then press the
[ENTER] button.
The Hardware Setup menu appears.
3
Use the Up/Down [
]/[
] but-
tons to select “3. Remote Setup,”
and then press the [ENTER] but-
ton.
The Remote Setup menu appears.
4
Use the Up/Down [
]/[
] but-
tons to select “b. Remote ID,” and
then use the Left/Right [
]/[
]
buttons to select an ID: 1
(default), 2, or 3.
ENTER
ENTER
ENTER
ENTER
ENTER
TX-NR901_En.book Page 48 Wednesday, October 1, 2003 9:44 AM