Onkyo TX-SR608 Owner Manual - Page 41

■ Speakers Type ` Normal: Select this if you've connected your front speakers normally. ` Bi-Amp: Select this if you've bi-amped your front speakers. Note • Powered Zone 2 cannot be used if "Speakers Type" is set to "Bi-Amp" (➔ 56). ■ Speaker Terminal Assign Front High/Front Wide/Zone2 With this setting, you can specify the speakers connected to FRONT HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS terminals. `Front High: Front high speakers can be used. `Front Wide: Front wide speakers can be used. ` Zone2: Zone 2 speakers can be used. (Powered Zone 2 enabled). Note • If the "Speakers Type" setting is set to "Bi-Amp", or Powered Zone 2 cannot be used. SurrBack/Front High/Front Wide With this setting, you can specify the speakers connected to SURR BACK OR FRONT HIGH OR FRONT WIDE SPEAKERS terminals. `Surr Back: Surround back speakers can be used. `Front High: Front high speakers can be used. `Front Wide: Front wide speakers can be used. Note • If the "Speakers Type" setting is set to "Bi-Amp", or Powered Zone 2 cannot be used. • If "Front High" is selected in the "Front High/Front Wide/ Zone2" setting, you cannot select "Front High" here. • If "Front Wide" is selected in the "SurrBack/Front High/ Front Wide" setting, you cannot select "Front Wide" here. Speaker Configuration With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify "Full Band" for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker's manuals to determine the optimum crossover frequencies. If you set up your speakers using Audyssey 2EQ® Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to "80Hz(THX)" crossover. ■ Subwoofer ` Yes: Select if a subwoofer is connected. ` No: Select if no subwoofer is connected. ■ Front ` Full Band ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz Note • If the "Subwoofer" setting is set to "No", the "Front" setting is fixed at "Full Band". ■ Center*1, Surround*1, Surr Back*2*3*4*5 ` Full Band ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None: Select if no speaker is connected. ■ Front Wide*1*2*4*6, Front High*1*2*4*7 ` Full Band ` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None: Select if no speaker is connected. Note *1 "Full Band" can be selected only when "Full Band" is selected in the "Front" setting. *2 If the "Surround" setting is set to "None", this setting cannot be selected. *3 If the "Surround" setting is set to anything other than "Full Band", "Full Band" cannot be selected here. *4 If the "Speakers Type" setting is set to "Bi-Amp" (➔ 41), or Powered Zone 2 is being used (➔ 56), this setting cannot be selected. *5 If you have selected other than "Surr Back" in the "SurrBack/Front High/Front Wide" setting, this setting cannot be selected. *6 If you have selected other than "Front Wide" in the "Front High/Front Wide/Zone2" or "SurrBack/Front High/Front Wide" setting, this setting cannot be selected. *7 If you have selected other than "Front High" in the "Front High/Front Wide/Zone2" or "SurrBack/Front High/Front Wide" setting, this setting cannot be selected. ■ Surr Back Ch ` 1ch: Select if only one surround back speaker L is connected. ` 2ch: Select if two (left and right) surround back speakers are connected. Note • If the "Surr Back" Setting is set to "None" (➔ 48), this setting cannot be selected. En 41