Optoma ZK750 ZK1050_UM - Page 22

USING THE PROJECTOR, Powering on / off the projector

Get Optoma ZK750 PDF manuals and user guides View all Optoma ZK750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

USING THE PROJECTOR Powering on / off the projector Powering on 1. Securely connect the AC power cord and signal/source cable to the projector. 2. Set the power switch to the "I" (ON) position and wait until the power button " " on the projector keypad is solid orange. 3. Turn on the projector by pressing the ON button " " on the remote control or the power button " " on the projector keypad. The status LED is orange with a long blink and the status LED will turn to solid green. ON OFF or 1 2 3 4 5 6 Note: If the projector is turned on fo7r the fi8rst time9, you will be prompted to select the projector language, projection orientation, and other settings. Powering off Info 0 Mode 1. Turn off the projector bAyutopressing thIenpupt ower button " " on the projector keypad or the OFF button " " on the remote control. A message will pop up to confirm that you want to turn off the projector. 2. Press the power button or thEentOerFF button again to confirm, otherwise the warning message disappears after 10 seconds and the projector remains on. 3. Set the Power switch to the "o" (OFF) position. 4. Disconnect the powerMcenourd from theEpxitrojector and the electrical outlet. Gamma Bright Cont. PIP Note: It is not recommended to turn on the projector immediately after powering off the projector. 22 English Lens H Lens V Focus

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
English
22
USING THE PROJECTOR
Powering on / off the projector
Powering on
1.
Securely connect the AC power cord and signal/source cable to the projector.
2.
Set the power switch to the “
I
“ (ON) position and wait until the power button “
” on the projector
keypad is solid orange.
3.
Turn on the projector by pressing the
ON
button “
” on the remote control or the power button “
” on
the projector keypad.
The status LED is orange with a long blink and the status LED will turn to solid green.
ON
OFF
2
1
3
5
4
6
or
Note:
If the projector is turned on for the first time, you will be prompted to select the projector language, projection
orientation, and other settings.
Powering off
1.
Turn off the projector by pressing the power button “
” on the projector keypad or the
OFF
button “
”
on the remote control.
A message will pop up to confirm that you want to turn off the projector.
2.
Press the power button or the
OFF
button again to confirm, otherwise the warning message disappears
after 10 seconds and the projector remains on.
3.
Set the Power switch to the “
o
” (OFF) position.
4.
Disconnect the power cord from the projector and the electrical outlet.
Note:
It is not recommended to turn on the projector immediately after powering off the projector.