Panasonic AWE860 AWE860 User Guide - Page 28

Caution, Color phase adjustment, ADJUSTMENT by CAMERA], ADJUSTMENT with RCU RCB, Hybrid control panel]

Get Panasonic AWE860 - COLOR CAMERA PDF manuals and user guides View all Panasonic AWE860 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Adjustment Caution: • When horizontal phase adjustment is required using RCU (RCB) or hybrid control panel, BAR/CAM switch should be set to BAR. Horizontal phase cannot be adjusted if the switch is in the CAM position. After adjustment set BAR/CAM switch back to CAM. • When horizontal phase adjustment is moved, color phase is also moved. Adjust color phase whenever horizontal phase adjustment is moved. U Color phase adjustment Supply the output signal (split color bar) from the color special effect generator to a color monitor or vectorscope. Adjust the color phase of the camera. 4. Select [SC Fine] on the sub menu. Perform fine adjustment with the YES/ABC switch and the NO/BAR switch. Color bar of camera Sprit line Color bar of special effects generator [ADJUSTMENT by CAMERA] 1. Press the NO/BAR switch for over 5 seconds for the color bar mode. 2. Select [G/L Adjustment] on the main menu, then select [SC Coarse] on the sub menu. 3. Make coarse adjustment with the YES/ABC switch and the NO/BAR switch. [ADJUSTMENT with RCU (RCB, Hybrid control panel)] Use the subcarrier phase coarse adjustment control and subcarrier phase fine control. ❈ It is recommended that a vectorscope be used for maximum accuracy in color phase adjustment. Caution: • When color phase adjustment is required using RCU (RCB) or hybrid control panel, BAR/CAM switch should be set to BAR. Color phase cannot be adjusted if the switch is in the CAM position. After adjustment set BAR/CAM switch back to CAM. • When horizontal phase adjustment is moved, color phase is also moved. Adjust color phase whenever horizontal phase adjustment is moved. -28-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
-28-
Caution:
• When horizontal phase adjustment is required using RCU
(RCB) or hybrid control panel, BAR/CAM switch should be
set to BAR. Horizontal phase cannot be adjusted if the
switch is in the CAM position. After adjustment set
BAR/CAM switch back to CAM.
• When horizontal phase adjustment is moved, color phase
is also moved. Adjust color phase whenever horizontal
phase adjustment is moved.
U
Color phase adjustment
Supply the output signal (split color bar) from the color
special effect generator to a color monitor or vectorscope.
Adjust the color phase of the camera.
[ADJUSTMENT by CAMERA]
1.
Press the NO/BAR switch for over 5 seconds for the color
bar mode.
2.
Select [G/L Adjustment] on the main menu, then select
[SC Coarse] on the sub menu.
3.
Make coarse adjustment with the YES/ABC switch and
the NO/BAR switch.
4.
Select [SC Fine] on the sub menu. Perform fine
adjustment with the YES/ABC switch and the NO/BAR
switch.
[ADJUSTMENT with RCU (RCB, Hybrid control panel)]
Use the subcarrier phase coarse adjustment control and
subcarrier phase fine control.
❈
It is recommended that a vectorscope be used for
maximum accuracy in color phase adjustment.
Caution:
• When color phase adjustment is required using RCU
(RCB) or hybrid control panel, BAR/CAM switch should be
set to BAR. Color phase cannot be adjusted if the switch is
in the CAM position. After adjustment set BAR/CAM switch
back to CAM.
• When horizontal phase adjustment is moved, color phase
is also moved. Adjust color phase whenever horizontal
phase adjustment is moved.
Color bar of camera
Color bar of special
effects generator
Sprit line
Adjustment