Panasonic DMRE60 DMRE60 User Guide - Page 25

Timer recording Manually programming timer recordings You can enter up to 16 programs up to a month in advance. Each daily or weekly program is counted as one program. 1 Press [PROG/CHECK]. A line that is ready for programming is highlighted. TIMER RECORDING No CHANNEL 01 64 ABC Remaining Recording Time 1:58 SP 3/26 TUE 12:55 PM DATE ON OFF MODE CHECK 3/ 26 TUE 1:00 PM 2:00 PM SP Enable New Timer Program SELECT ENTER CANCEL RETURN 2 Press [ENTER]. Press ENTER or VCR Plus+ to store new program TIMER RECORDING CHANNEL --3-- 4 Remaining Recording Time 1:58 SP 3/26 TUE 12:55 PM DATE ON OFF MODE Enter Title Please set Channel. SELECT ENTER RETURN No. 0 -- 9 3 Press [1] to move through the items and change the items with [3, 4]. ≥The current settings are shown each time you press [1]. ≥You may use the numbered buttons to enter the CHANNEL, DATE, ON (start Time), and OFF (Finish Time). TIMER RECORDING Remaining Recording Time 1:58 SP 3/26 TUE 12:55 PM CHANNEL DATE ON OFF MODE 64 ABC 3/ 26 TUE 2:30 PM 3:00 PM SP Enter Title ≥CHANNEL (Channel number and caption) ≥ DATE [.Current date l ;: l Next day up to one month later minus one day l ;: l Weekly timer: SUN-SAT>MON-SAT>MON-FRI l ;: {.Daily timer: WEEKLY SUN>--->WEEKLY SAT ≥ON (Start time)/OFF (Finish time) The time increases or decreases in 30-minute increments if you hold the button. ≥MODE (Recording mode ➜page 10) SP>XP>FR>EP>LP (>Return to SP) ≥Enter Title Select "Enter Title" using [2, 1] and press [ENTER] (➜page 27). 4 Press [ENTER] when you have finished programming the timer. TIMER RECORDING No CHANNEL 01 64 ABC 02 64 ABC Remaining Recording Time 1:58 SP 3/26 TUE12:55 PM DATE ON OFF MODE CHECK 3/ 26 TUE 1:00 PM 2:00 PM SP Enable 3/ 26 TUE 2:30 PM 3:00 PM SP Enable New Timer Program Displayed if the recording can fit in the remaining space on the disc. ≥Press [3, 4] to select "New Timer Program" and repeat steps 2- 4 to program other recordings. 5 Press [PROG/CHECK] or [RETURN]. The timer recording list disappears and the message "TURN RECORDER OFF FOR TIMER RECORDING" is shown on the television. 6 Press [Í, DVD POWER]. Ensure "F" lights on the unit's display. To release the unit from recording standby If you want to record something else before the program start time, for example: Press [Í, DVD POWER]. The unit turns on and "F" goes out. ≥Be sure to press [Í, DVD POWER] to return the unit to standby mode before the scheduled recording time. Timer recording will work only if "F" is displayed. To stop recording when recording has already begun Press [∫], then [ENTER] within 5 seconds on the remote. Recording stops. [Note] ≥The actual time recorded may be longer than the program itself when television programs are recorded using VCR Plusi. ≥If you don't select a recording mode when using VCR Plus+ codes to make a timer recording, the unit sets the mode selected on the unit at that time (unless the mode is "XP", in which case the unit sets "FR" as the mode). ≥"All timer programs are occupied." appears if there are already 16 programs. ≥The remaining time displayed is based on the current recording mode. ≥When you program successive timer recordings to start immediately one after the other, the unit cannot record the part at the beginning of the later programs (a few seconds when recording with DVD-RAM and approximately 30 seconds when recording with DVD-R). ≥If you set DST (Daylight Saving Time) to ON when manually setting the clock (➜page 47), timer recording may not work when summer switches to winter and vice versa. ≥"F" flashes when the unit couldn't go to timer recording standby (e.g., a disc isn't loaded, a disc that can't be recorded to is loaded, or the disc is protected). Check the disc carefully. 25 RQT6981