Panasonic MCV415 MCV415 User Guide - Page 32

REPLACING BELT, Lift Agitator Up, Felt Packing, Rear Belt, Cover, Install New Belt, Motor Shaft

Get Panasonic MCV415 - COMMERCIAL VACUUM PDF manuals and user guides View all Panasonic MCV415 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Replacing Belt + Rear Belt + Cover Couvre- courroie arrière Cubierta de la correa trasera Felt Packing Cale en feutre Empaquetadura de filtro Lift Agitator Up Soulever l'agitateur Unidad del agitador Motor Shaft Arbre d'entraînement du moteur Eje del motor Install New Belt Poser la nouvelle courroie Instalación de la correa + + Groove Ouverture Ranura End Cap Bouchon Tapa del extremo ➢ Replace belt whenever a burning rubber smell caused by excessive slippage occurs. ➢ Remove lower plate. ➢ Lift rear belt cover and remove felt packing. ➢ Remove agitator by carefully lifting out. ➢ Remove worn or broken belt. ➢ Clean agitator. ➢ Loop new belt (Type UB8 only) around motor shaft and agitator pulley; see illustration for correct belt routing. ➢ Reinstall felt packing. ➢ Reinstall agitator back into nozzle housing grooves. ➢ Close rear belt cover and reinstall felt packing. ➢ After reinstalling the agitator, turn it by hand to make sure that belt is not twisted or pinched and that all rotating parts turn freely. ➢ Reinstall lower plate. - 32 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Replacing Belt
+
+
Lift Agitator Up
Soulever l’agitateur
Unidad del agitador
Felt Packing
Cale en feutre
Empaquetadura
de filtro
Rear Belt
Cover
Couvre-
courroie
arrière
Cubierta
de la correa
trasera
Install New Belt
Poser la nouvelle courroie
Instalación de la correa
Motor Shaft
Arbre
d’entraînement
du moteur
Eje del motor
Replace belt whenever a burning
rubber smell caused by excessive
slippage occurs.
Remove lower plate.
Lift rear belt cover and remove felt
packing.
Remove agitator by carefully lifting
out.
Remove worn or broken belt.
Clean agitator.
Loop new belt (Type UB8 only)
around motor shaft and agitator
pulley; see illustration for correct belt
routing.
Reinstall felt packing.
Reinstall agitator back into nozzle
housing grooves.
Close rear belt cover and reinstall felt
packing.
After reinstalling the agitator, turn it
by hand to make sure that belt is not
twisted or pinched and that all
rotating parts turn freely.
Reinstall lower plate.
+
+
Groove
Ouverture
Ranura
End Cap
Bouchon
Tapa del extremo
- 32 -