Panasonic MX-ZX1800 MX-ZX1800 Owner s Manual - Page 10

How to Clean ¾ Unplug before cleaning. ¾ Clean the product before your first use and after each use. ¾ Do not clean the blender before it cools down. ¾ Remove any demountable parts before cleaning. ¾ Some discoloration may occur upon usage but it does not affect usage. CAUTION: Parts that can be washed in a dishwater t
3FNPWF
BOZ
SFTJEVF
GSPN
UIF
QBSU
CFGPSF
putting it into the dishwasher. t
High temperature may damage the parts, so please keep the parts away from any heat radiating devices, or lower their temperature. t
Do not use benzine, thinner, alcohol, bleach, polishing powder, metal brushes or nylon brushes, otherwise the surface will be damaged. t
%P
OPU
XBTI
UIF
NPUPS
IPVTJOH
BOE
DPOUBJOFS
CBTF
JO
B
EJTIXBTIFS t
%P
OPU
DMFBO
UIF
BQQMJBODF
XJUI
B
QPJOUFE
PCKFDU
TVDI
BT
B
UPPUIQJDL
PS
QJO Cap/Cover/Cover gasket Wash with diluted dish soap (neutral) and a soft sponge. Then rinse thoroughly with water and dry well. t
%JTBTTFNCMF
UIF
DPWFS
HBTLFU * Dishwasher safe Blender container/Container gasket/Drip tray Wash with diluted dish soap (neutral) and a soft sponge. Then rinse thoroughly with water and dry well. t
Before cleaning, be sure to take out the container gasket (it might be lost during the cleaning process). * Dishwasher safe Blender container base Wash with diluted dish soap (neutral) and a soft sponge. Then rinse thoroughly with water and dry well. CAUTION: Pay attention when handling the blender container base. Blade is sharp. * NOT dishwasher safe Tamper/Container base holder Wash with diluted dish soap (neutral) and a soft sponge. Then rinse thoroughly with water and dry well. Motor housing/Ice pack Wipe with a well-wrung cloth. Assemble/Disassemble the tamper by referring to the above figure. * Dishwasher safe &/ Note After the ice pack is clean and dry, keep it in the refrigerator for next use. * NOT dishwasher safe Troubleshooting ¾ Please check following points before arranging for service. Problem $BVTF
BOE
"DUJPO ⾣ The appliance does not turn on. µ The power plug is not in the outlet. ÷ Insert the plug down to the root. µ The power switch is not turned on. ÷ Turn on the power switch that is located in the back. µ The overload protection was triggered. ÷ Press the reset button on the bottom of the motor housing (P. EN21). No auto menu can be selected. ⾣ µ The blender container is not set correctly. ÷ Re-set blender container correctly. (P. EN14) µ Manual mode or an auto menu selection is chosen during blending. ÷ Select an auto menu selection or manual mode after motor is stopped. µ Buttons are pressed while wearing gloves. ÷ Press the buttons with a bare hand. µ The button was pressed with a wet hand. ÷ Dry your hand and press the button again. µ Button not pressed. ÷ Be sure to press on the illustration of the button. &WFO
UIPVHI
UIF
QPXFS
is on, the appliance does not start blending. ⾣ µ The blender container is not set correctly. ÷ Re-set blender correctly. µ An auto menu selection or manual mode is not selected. ÷ Select an auto menu selection or manual mode. µ The ingredients are jammed. ÷ Take out ingredients from the blender container and put them back in. Chosen menu selection is cancelled. (All menu's indicators are flashing.) ⾣ µ The stop/start key is not pressed within 10 seconds after menu selection is chosen. ÷ Menu selection is cancelled after 10 seconds of inactivity for the prevention of a motor operation malfunction. Select an auto menu selection or manual mode again and press " " within 10 seconds. Time on the auto NFOVT
DBO
BEKVTU
POMZ
QBSU
PG
UIF
XBZ ⾣ µ Maximum and minimum blending time is set for each menu and varies. ÷ Adjust the time to be in the each menu selection's range. (P. EN12) The appliance stops during blending. ⾣ µ The overload protection is activated.
ɾToo many ingredients
ɾBlending hard ingredients
ɾAbnormal noise or vibration ÷ Release the overload protection. (P. EN21) ɾUsing sticky ingredients ÷ Add liquid. µ Maximum operating time (approximately 9 minutes 40 seconds) is exceeded. ÷ Turn off the power and resume after 10 minutes of rest. µ The safety lock is activated due to tilt blender container when using the tamper. ÷ Re-start and hold the lid while using the tamper. &/ English