Panasonic U1 Panaboard - Page 46

Electronic Board Operations Check

Get Panasonic U1 - Toughbook - Atom Z520 PDF manuals and user guides
UPC - 092281895208
View all Panasonic U1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Electronic Board Operations Check After assembling the unit, perform the procedures presented in the following table to make sure it functions properly. Step Points to Check Condition Solutions 1 Turn the power switch on. Time set-up message is displayed (Normal operation) after initial message is displayed. (If not) Check the power cord. (See step 8 on page 45.) 2 Set the time. (Refer to "Setting the current time" on page 20.) The time can be set. The time cannot be set. (Normal operation) Contact the store or dealer from which the unit was purchased. 3 Connect a USB flash memory device or SD memory card. (Refer to "Scanning" on page 14.) The USB flash memory device or SD memory card installed is recognized and is shown on the display. (Normal operation) (If not) Contact the store or dealer from which the unit was purchased. 4 Use the accessory marker to The scanner moves smoothly and (Normal operation) the scanned image appears on the draw a large across display. the entire scannable area of the whiteboard surface. • For information on the scannable area, refer to "Whiteboard" on page 10. Press the Start/Stop key. The scanner does not move smoothly. A strange noise is made. The scanned image is not displayed. Check the connector. (See step 7 on page 45.) Check the scanner attachment. (See step 7 on page 45.) Contact the store or dealer from which the unit was purchased. The entire scannable area is not scanned. 5 Zoom in on several areas of the The image on the display matches (Normal operation) scanned image. the image on the whiteboard. (See page 15 or 16.) A black or white horizontal line Check the white balance area, appears on the scanned image, or scanner lens and strong lighting. the image scanned is dark or (Refer to "Troubleshooting" on blank. page 32.) 6 Rotate the whiteboard. (Refer to "Rotating the Whiteboard" on page 18.) The whiteboard can be rotated normally. The whiteboard cannot be rotated. (Normal operation) Check the whiteboard attachment. (See step 6 on page 44.) 7 Turn off the power switch, then turn back on after 3 minutes. The standby message is displayed after the initial message is displayed. (Normal operation) The time is not correct. Check the battery. (See page 31.) 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
46
Electronic Board Operations Check
After assembling the unit, perform the procedures presented in the following table to make sure it functions properly.
Step
Points to Check
Condition
Solutions
1
Turn the power switch on.
Time set-up message is displayed
after initial message is displayed.
(Normal operation)
(If not)
Check the power cord. (See
step 8 on page 45.)
2
Set the time.
(Refer to “Setting the current
time” on page 20.)
The time can be set.
(Normal operation)
The time cannot be set.
Contact the store or dealer from
which the unit was purchased.
3
Connect a USB flash memory
device or SD memory card.
(Refer to “Scanning” on page
14.)
The USB flash memory device or
SD memory card installed is
recognized and is shown on the
display.
(Normal operation)
(If not)
Contact the store or dealer from
which the unit was purchased.
4
Use the accessory marker to
draw a large
across
the entire scannable area of
the whiteboard surface.
•
For information on the
scannable area, refer to
“Whiteboard” on page 10.
Press the Start/Stop key.
The scanner moves smoothly and
the scanned image appears on the
display.
(Normal operation)
The scanner does not move
smoothly.
Check the connector.
(See step 7 on page 45.)
A strange noise is made.
Check the scanner attachment.
(See step 7 on page 45.)
The scanned image is not
displayed.
Contact the store or dealer from
which the unit was purchased.
The entire scannable area is not
scanned.
5
Zoom in on several areas of the
scanned image.
(See page 15 or 16.)
The image on the display matches
the image on the whiteboard.
(Normal operation)
A black or white horizontal line
appears on the scanned image, or
the image scanned is dark or
blank.
Check the white balance area,
scanner lens and strong lighting.
(Refer to “Troubleshooting” on
page 32.)
6
Rotate the whiteboard.
(Refer to “Rotating the
Whiteboard” on page 18.)
The whiteboard can be rotated
normally.
(Normal operation)
The whiteboard cannot be rotated.
Check the whiteboard
attachment.
(See step 6 on page 44.)
7
Turn off the power switch, then
turn back on after 3 minutes.
The standby message is displayed
after the initial message is
displayed.
(Normal operation)
The time is not correct.
Check the battery.
(See page 31.)