Panasonic WJ-NV300 Operating Instructions - Page 58

Con the settings relating to NTP/SNMP synchronization [NTP/SNMP], NTP setup, Time adjustment]

Get Panasonic WJ-NV300 PDF manuals and user guides View all Panasonic WJ-NV300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Configure the settings relating to NTP/SNMP synchronization [NTP/SNMP] The settings to synchronize the system clock with the NTP (Network Time Protocol) and SNMP (Simple Network Management Protocol) server can be configured on this tab. Note: • Entering "http://" is not necessary if the server name is entered. ■ SNMP setup Set this item to check the status of the recorder by connecting to the SNMP server. Enter the items using the alphanumeric characters listed in "Note" (☞ page 56) and symbols. ■ NTP setup [Time adjustment] Select "On" or "Off" to determine whether or not to adjust the time according to the NTP server. On: Adjusts the time automatically. Off: Does not adjust the time automatically. Default: Off Important: • Inaccuracy of time stamp on recorded images due to inaccurate clock adjustment of this product may cause operational problems. When the system operation requires an accurate time setting, use the NTP auto time adjustment using an NTP server. [Community] Enter a name used for SNMP authentication (up to 32 alphanumeric characters). [System name] Enter a name (up to 255 alphanumeric characters) for management of the recorder by the SNMP system. Example: No.1 [Location] Enter a location where the recorder is installed. (up to 255 alphanumeric characters) Example: 2F [Contact] Enter the contact information such as a mail address of an administrator of this recorder. (up to 255 alphanumeric characters) [Primary server address] [Secondary server address] Enter the address or name of the NTP server when adjusting the time using the NTP server. The name of the NTP server is available only when "Manual" is selected for "DNS" on the [Basic] tab accessed from the "Advanced setup" menu - the "Network" page of the setup menu. Enter up to 255 alphanumeric characters including hyphens (-) and periods (.). Important: • It is possible to run the recorder as an NTP server to be referred by the cameras. In this case, set the port number of the camera to "123". Refer to the operating instructions of the connected camera for information on how to configure the settings of the camera. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
58
Configure the settings relating to NTP/SNMP synchronization
[NTP/SNMP]
The settings to synchronize the system clock with the NTP (Network Time Protocol) and SNMP (Simple Net-
work Management Protocol) server can be configured on this tab.
■
NTP setup
[Time adjustment]
Select "On" or "Off" to determine whether or not to
adjust the time according to the NTP server.
On: Adjusts the time automatically.
Off: Does not adjust the time automatically.
Default:
Off
Important:
Inaccuracy of time stamp on recorded images due
•
to inaccurate clock adjustment of this product
may cause operational problems. When the sys-
tem operation requires an accurate time setting,
use the NTP auto time adjustment using an NTP
server.
[Primary server address]
[Secondary server address]
Enter the address or name of the NTP server when
adjusting the time using the NTP server.
The name of the NTP server is available only when
"Manual" is selected for "DNS" on the [Basic] tab
accessed from the "Advanced setup" menu - the
"Network" page of the setup menu.
Enter up to 255 alphanumeric characters including
hyphens (-) and periods (.).
Important:
It is possible to run the recorder as an NTP server
•
to be referred by the cameras. In this case, set the
port number of the camera to "123". Refer to the
operating instructions of the connected camera
for information on how to configure the settings of
the camera.
Note:
Entering "http://" is not necessary if the server
•
name is entered.
■
SNMP setup
Set this item to check the status of the recorder by
connecting to the SNMP server.
Enter the items using the alphanumeric characters
listed in "Note" (
☞
page 56) and symbols.
[Community]
Enter a name used for SNMP authentication (up to 32
alphanumeric characters).
[System name]
Enter a name (up to 255 alphanumeric characters) for
management of the recorder by the SNMP system.
Example: No.1
[Location]
Enter a location where the recorder is installed. (up to
255 alphanumeric characters)
Example: 2F
[Contact]
Enter the contact information such as a mail address
of an administrator of this recorder. (up to 255 alpha-
numeric characters)