Panasonic WVCP464 WVCP460 User Guide - Page 2

Features, Major Operating Controls And Their Functions, Connections - wv cp464 manual

Page 2 highlights

FEATURES 1. The following functions are built in. (1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) The SUPER-D2 function eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. Dynamic range of 46 dB. (3) Various External Sync Functions, including Gen-Lock (4) Auto/Manual White Balance Function (5) Electronic Shutter Function 2. Signal-to-noise ratio of 50 dB 3. Minimum illumination of 0.8 lx (0.08 footcandle) with F 1.4 lenses. 4. Minimum illumination of 0.4 lx (0.04 footcandle) with Panasonic aspherical high speed (F0.75) lenses. 5. 480 lines of horizontal resolution MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS q we r Super Dynamic WV-CP460 LOCK !4 120V AC 60Hz VIDEO OUT GEN-LOCK !3 !2 !1 i t Hi-Z G/L 75Ω o y u !0 !5 DC 12V AC 24V IN IN 1 2 GND VIDEO OUT GEN-LOCK !3 !2 Slide the panel to the left until it locks. q Auto Iris Lens Connector This connector is used to connect the auto iris lens with a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100). w Focus Fixing Screw e Flange-back Adjusting Ring This ring is used to adjust the back focal length or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CS-mount lens. r Lens (Option) t Camera Mounting Screw Hole This hole is used to mount the camera onto a mounting bracket. CONNECTIONS A. WV-CP460 (120 V AC 60 Hz) 1. Plug the AC power cord (supplied as standard accessory) into the AC Inlet Socket. 2. Connect the AC power cord to a 120V AC 60 Hz outlet. Notes: • Connect the power cord firmly. • The power cord should be long enough for panning and tilting. If the cable is too short, the power cord plug may be pulled off the camera when the camera pans or tilts. B. WV-CP464 (12 V DC/24 V AC) The WV-CP464 has an AC/DC compatible input terminal. The 12 V DC or 24 V AC power supply cord can be connected to this terminal. The camera detects the power source automatically. 1. 12 V DC Power Supply Connect the power cord to the AC/DC compatible input terminal on the rear panel of the camera. DC 12V AC 24V IN IN 1 2 GND 12 V DC (10.8 V - 16 V) Resistance of copper wire [at 20°C (68°F)] Copper wire #24 #22 #20 #18 size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2) Resistance Ω/m 0.078 0.050 0.030 0.018 Resistance Ω/ft 0.026 0.017 0.010 0.006 • Calculation of maximum cable length between camera and power supply 10.8 V DC ≤ VA - (R x 0.42 x L) ≤ 16 V DC L : Cable length (m) R : Resistance of copper wire (Ω/m) VA : DC output voltage of power supply unit VA − 12 L standard = (m) 0.42 x R VA − 16 L minimum = (m) 0.42 x R VA − 10.5 L maximum = (m) 0.42 x R

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11

1.
The following functions are built in.
(1)
Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D
2
function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB.
(3)
Various External Sync Functions, including Gen-Lock
(4)
Auto/Manual White Balance Function
(5)
Electronic Shutter Function
2.
Signal-to-noise ratio of 50 dB
3.
Minimum illumination of 0.8 lx (0.08 footcandle) with F 1.4 lenses.
4.
Minimum illumination of 0.4 lx (0.04 footcandle) with Panasonic aspherical high speed
(F0.75) lenses.
5.
480 lines of horizontal resolution
FEATURES
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q
Auto Iris Lens Connector
This connector is used to connect the auto iris lens with a 4-pin male connector sup-
plied as a standard accessory (Part No.
YFE4191J100).
w
Focus Fixing Screw
e
Flange-back Adjusting Ring
This ring is used to adjust the back focal length or picture focus.
Rotate this ring clock-
wise for a C-mount lens or counterclockwise for a CS-mount lens.
r
Lens (Option)
t
Camera Mounting Screw Hole
This hole is used to mount the camera onto a mounting bracket.
<WV-CP460>
<WV-CP464>
q
e
w
r
t
y
o
u!
0
!
1
i
!
2
!
3
!
2
!
5
!
3
!
4
Super
Dynamic
WV-
CP460
Hi-Z
G/L 75
VIDEO OUT
120V
AC
60Hz
GEN-LOCK
AC
24V
IN
DC
12V
IN
1
2
VIDEO OUT
GND
GEN-LOCK
LOCK
Slide the panel to the left until it locks.
CONNECTIONS
A. WV-CP460 (120 V AC 60 Hz)
1.
Plug the AC power cord (supplied as standard accessory) into the AC Inlet Socket.
2.
Connect the AC power cord to a 120V AC 60 Hz outlet.
Notes:
Connect the power cord firmly.
The power cord should be long enough for panning and tilting.
If the cable is too short, the power cord plug may be pulled off the camera when the
camera pans or tilts.
B. WV-CP464 (12 V DC/24 V AC)
The WV-CP464 has an AC/DC compatible input terminal.
The 12 V DC or 24 V AC power
supply cord can be connected to this terminal.
The camera detects the power source auto-
matically.
AC
24V
IN
DC
12V
IN
1
2
GND
12 V DC
(10.8 V - 16 V)
Copper wire
#24
#22
#20
#18
size (AWG)
(0.22mm
2
) (0.33mm
2
) (0.52mm
2
) (0.83mm
2
)
Resistance
0.078
0.050
0.030
0.018
/m
Resistance
0.026
0.017
0.010
0.006
/ft
Resistance of copper wire [at 20°C (68°F)]
Calculation of maximum cable length between camera and power supply
10.8 V DC
V
A
- (R x 0.42 x L)
16 V DC
L
: Cable length (m)
R
: Resistance of copper wire (
/m)
V
A
: DC output voltage of power supply
unit
V
A
12
L standard =
(m)
0.42 x R
V
A
16
L minimum =
(m)
0.42 x R
V
A
10.5
L maximum =
(m)
0.42 x R
1.
12 V DC Power Supply
Connect the power cord to the AC/DC compatible input terminal on the rear panel of the
camera.