Pentax AF360FGZ Operation Manual - Page 44

The two flash units must be set to the same, channel, otherwise the separated flash unit will

Get Pentax AF360FGZ - AF - Hot-shoe clip-on Flash PDF manuals and user guides
UPC - 027075121041
View all Pentax AF360FGZ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

 Slide the setting switch back up to the (white dot).  When you turn the camera on and press the shutter release button halfway down, the channel of the flash unit is registered on the camera. (Preparation of Separated Flash Unit) 2 Next, set the channel of the separated (wireless) flash unit to the same channel as the flash unit attached to the camera.  Place the other AF360FGZ in the desired position.  Set the power switch of the flash unit to (WIRELESS).  Set the wireless mode switch to (S), so that SLAVE is displayed in the upper right corner of the LCD panel.  Slide down the setting switch to the (yellow dot) to display the channel on the LCD panel.  Press the channel button (CH) and select the same channel that the flash unit attached to the camera has been set to.  Slide the setting switch back up to the (white dot). ● The two flash units must be set to the same channel, otherwise the separated flash unit will not discharge. (Photographing) 3 Confirm that both flash units are fully charged, and take the photograph. A lamp on the wireless flash unit will blink. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
42
Slide the setting switch back up to the (white
dot).
When you turn the camera on and press the
shutter release button halfway down, the
channel of the flash unit is registered on the
camera.
(Preparation of Separated Flash Unit)
Next, set the channel of the separated (wireless)
flash unit to the same channel as the flash unit
attached to the camera.
Place the other AF360FGZ in the desired
position.
Set the power switch of the flash unit to
(WIRELESS).
Set the wireless mode switch to (S), so that
SLAVE is displayed in the upper right corner of
the LCD panel.
Slide down the setting switch to the (yellow
dot) to display the channel on the LCD panel.
Press the channel button (CH) and select the
same channel that the flash unit attached to
the camera has been set to.
Slide the setting switch back up to the (white
dot).
●
The two flash units must be set to the same
channel, otherwise the separated flash unit will
not discharge.
(Photographing)
Confirm that both flash units are fully charged,
and take the photograph.
A lamp on the wireless flash unit will blink.
2
3