Philips DVDR985A User manual - Page 11

Connecting to a TV Only, TV has an S-Video In Jack

Get Philips DVDR985A PDF manuals and user guides
UPC - 037849922774
View all Philips DVDR985A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Hookups (cont'd) 11 Connecting to a TV Only TV has an S-Video In Jack 4 Antenna or Cable TV Signal 2 Back of TV (example only) RIGHT AUDIO IN LEFT AUDIO IN S-AUDIO IN RIGHT AUDIO IN LEFT AUDIO IN S-VIDEO IN 1 EXT 2 EXT 3 COMPONENT VIDEO Y Y PB PB PR PR EXT 1 PROG SCAN Y L L PB PR R R EXT 1/2 EXT 3 L R 3 IN RC 6 1 Connect your Antenna or Cable TV signal to the ANTENNA jack on the rear of the DVD Recorder. 2 Connect the supplied S-Video cable to the S-VIDEO OUT (Y/C) (EXT 1) jack of the DVD Recorder and to the TV's S-VIDEO In jack. 3 Connect a supplied two-strand audio cable to the red and white AUDIO OUT (EXT 1/2) left and right jacks on the DVD Recorder and to the left/right AUDIO IN jacks on the TV. The supplied twostrand audio cable has red and white stripes on the cable ends. Match the cable stripe colors to the jack colors. 4 Connect the supplied power cord to the MAINS (AC Power) jack on the rear of the DVD Recorder. Connect the power cords of the DVD Recorder and the TV to a power outlet. 5 Press the STANDBY-ON y button on the front of the DVD Recorder to turn on the DVD Recorder. The STANDBY-ON light will turn green. If "TURN ON TV" appears on the display panel, you need to turn on your TV and set it to the correct S-Video In channel. (See next step.) This is part of the Initial Setup of the DVD Recorder. You cannot see the Initial Setup screens until you turn on the TV and have it on the right S-Video In channel. 6 Turn on the TV power. Set the TV to the S-Video In channel. This is not channel 3 or 4 as it might be when using a VCR. See your TV owner's manual for details. Or, go to your lowest TV channel and change channels down until you see the DVD background picture or Initial Setup screen on the TV screen. The Initial Setup screen will appear the first time you turn on the Recorder. Go to page 16 to continue. Helpful Hints • On the TV, the S-Video In jack may be labeled Y/C, S-Video, or S-VHS (super video). • If you plan to watch your TV with the DVD Recorder off, connect the supplied RF coaxial cable to the Recorder's TV jack and to the RF IN or ANTENNA IN jack (75 ohm) on your television. This lets you watch channels at the TV normally when the DVD Recorder is off and will improve the reception at your TV.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
1
Connect your Antenna or Cable TV signal to the ANTENNA jack
on the rear of the DVD Recorder.
2
Connect the supplied S-Video cable to the S-VIDEO OUT (Y/C)
(EXT 1) jack of the DVD Recorder and to the TV’s S-VIDEO In
jack.
3
Connect a supplied two-strand audio cable to the red and white
AUDIO OUT (EXT 1/2) left and right jacks on the DVD Recorder
and to the left/right AUDIO IN jacks on the TV.
The supplied two-
strand audio cable has red and white stripes on the cable ends. Match the
cable stripe colors to the jack colors.
4
Connect the supplied power cord to the MAINS (AC Power) jack
on the rear of the DVD Recorder.
Connect the power cords of the DVD Recorder and the TV to a
power outlet.
5
Press the STANDBY-ON
y
button on the front of the DVD
Recorder to turn on the DVD Recorder.
The STANDBY-ON light will
turn green.
If
“
TURN ON TV
”
appears on the display panel, you need to turn on your
TV and set it to the correct S-Video In channel. (See next step.) This is part
of the Initial Setup of the DVD Recorder. You cannot see the Initial Setup
screens until you turn on the TV and have it on the right S-Video In channel.
6
Turn on the TV power. Set the TV to the S-Video In channel.
This is
not channel 3 or 4 as it might be when using a VCR. See your TV owner
’
s
manual for details. Or, go to your lowest TV channel and change channels
down until you see the DVD background picture or Initial Setup screen on
the TV screen.
The Initial Setup screen will appear the first time you turn on the
Recorder. Go to page 16 to continue.
Hookups (cont’d)
11
Connecting to a TV Only
TV has an S-Video In Jack
COMPONENT VIDEO
PROG
SCAN
EXT 2
Y
Y
P
B
P
B
P
R
Y
L
L
L
R
R
R
P
B
P
R
P
R
EXT 3
EXT 3
EXT 1
EXT 1/2
IN
RC 6
Back of TV
(example only)
2
LEFT AUDIO IN
RIGHT AUDIO IN
3
S-VIDEO IN
4
Antenna
or Cable TV
Signal
1
•
On the TV, the S-Video In jack
may be labeled Y/C, S-Video, or
S-VHS (super video).
•
If you plan to watch your TV
with the DVD Recorder off, con-
nect the supplied RF coaxial
cable to the Recorder’s TV jack
and to the RF IN or ANTENNA
IN jack (75 ohm) on your tele-
vision. This lets you watch chan-
nels at the TV normally when
the DVD Recorder is off and
will improve the reception at
your TV.
Helpful Hints