Philips LC3631 User Manual - Page 39

Troubleshooting

Get Philips LC3631 PDF manuals and user guides View all Philips LC3631 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

XP LC6281/6285 EVA English 01-08-2003 17:52 Pagina 39 7.Troubleshooting > If a fault occurs, first check the points listed below before taking the projector for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service organisation. Warning Under no circumstances should you try to repair the projector yourself as this could invalidate the guarantee. Read as follows Problem - Possible cause • Solution Image is not or incorrectly displayed General - Mains lead is not correctly connected. • Correctly connect mains lead. - The filter holder is not installed correctly or is damaged. • Install the filter holder correctly (see 'Cleaning the dust filter' under 'Maintenance'). - Lamp holder cover is not closed correctly or the lamp holder is damaged. • Close the cover correctly (see 'Lamp replacement' under 'Maintenance'). - Signal cable not correctly connected. • Connect signal cable correctly. - The projector is in Off position. • Press y On-Standby to switch on the projector. - A/V Mute active. • Cancel A/V Mute. Note - Projector still uses settings of a previous detected source on the input. • Reset all projector settings in the 'Set up' menu ('Factory settings'). Please note that all other projector settings will be reset as well. In Component Video mode - Keystoning is applied on a high resolution component signal. • Decrease keystoning until the image is correctly displayed. For this use the Keystone buttons on the remote control or the 'Keystone' option in the 'Set up' menu. In Data mode - Input resolution is too high (and keystoning is applied). • If you wish to keep the keystone correction, decrease the input resolution until the image is correctly displayed. For this, refer to the User Guide or support information of the computer. • If you wish to keep the input resolution as it is, decrease keystoning until the image is correctly displayed. For this, use the Keystone buttons on the remote control or the 'Keystone' option in the 'Set up' menu. - Input resolution is too high (and no keystoning is applied). • Decrease the input resolution until the image is correctly displayed. For this, refer to the User Guide or support information of the computer. In case of YPbPr connection - 'YPbPr' is not selected in the menu and 'Auto Source' is activated. In this case 'Auto Source' will not recognize 'YPbPr'. • Select 'YPbPr' as projection source in the 'Set up' menu ('Auto Component Selection' sub menu). Philips Home Cinema Projector 39 English User guide LC 6281 / LC 6285

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
>
If a fault occurs, first check the points listed below before taking the projector for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service
organisation.
Under no circumstances should you try to repair the projector yourself as this could invalidate the
guarantee.
–
Possible cause
•
Solution
General
–
Mains lead is not correctly connected.
•
Correctly connect mains lead.
–
The filter holder is not installed correctly or is damaged.
•
Install the filter holder correctly (see ‘Cleaning the dust filter’ under ‘Maintenance’).
–
Lamp holder cover is not closed correctly or the lamp holder is damaged.
•
Close the cover correctly (see ‘Lamp replacement’ under ‘Maintenance’).
–
Signal cable not correctly connected.
•
Connect signal cable correctly.
–
The projector is in Off position.
•
Press
y
On-Standby to switch on the projector.
–
A/V Mute active.
•
Cancel A/V Mute.
–
Projector still uses settings of a previous detected source on the input.
•
Reset all projector settings in the ‘Set up’ menu (‘Factory settings’).
Please note that all other projector settings will be reset as well.
In Component Video mode
–
Keystoning is applied on a high resolution component signal.
•
Decrease keystoning until the image is correctly displayed. For this use the
Keystone
buttons on the remote control or the ‘Keystone’ option in the ‘Set up’ menu.
In Data mode
–
Input resolution is too high (and keystoning is applied).
•
If you wish to keep the keystone correction, decrease the input resolution until the image is
correctly displayed. For this, refer to the User Guide or support information of the computer.
•
If you wish to keep the input resolution as it is, decrease keystoning until the image is
correctly displayed. For this, use the
Keystone
buttons on the remote control or the
‘Keystone’ option in the ‘Set up’ menu.
–
Input resolution is too high (and no keystoning is applied).
•
Decrease the input resolution until the image is correctly displayed. For this, refer to the User
Guide or support information of the computer.
In case of YPbPr connection
–
’YPbPr’ is not selected in the menu and ‘Auto Source’ is activated. In this case ‘Auto Source’ will not
recognize ‘YPbPr’.
•
Select ‘YPbPr’ as projection source in the ‘Set up’ menu (‘Auto Component Selection’ sub
menu).
Warning
Read as follows
Problem
Image is not or incorrectly
displayed
Note
Philips Home Cinema Projector
39
English
User guide
LC 6281 / LC 6285
7.Troubleshooting
XP LC6281/6285 EVA English
01-08-2003
17:52
Pagina 39