Pioneer 504CMX Technical Manual - Page 33

a State display, b Test chart display

Get Pioneer 504CMX - PDP - 50inch Plasma Panel PDF manuals and user guides
UPC - 012562689784
View all Pioneer 504CMX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

4. Installing and Using Software 4.2.4 Test Mode This is a service mode. Click "Test Mode" under "Hardware Information" in the CBdrvU task tray to open the screen shown below. a) State display This screen shows results of hardware checks and the state of the driver and the operating system (Windows). [Function overview] ¶ Driver Software Ver: Pen Button (small): Service Ver: Firmware Ver: ¶ System Buttons: L: R: M: Mouse pos: Angle: IP Address: Computer Name: Service Mode: Test chart display: Indicate the version of the CBdrvU setup program Indicate the setting of the small pen button in the Property screen Indicate the version of the USB filter driver Indicate the version of the scan device firmware G : Correctly recognized ✻ : Not correctly recognized (during 3-button mouse emulation) Left mouse button Right mouse button Middle mouse button Indicate mouse coordinates recognized by Windows Indicate currently set rotate angle Indicate IP address of the connected PC Indicate the name of the connected PC Indicate scan device service information and DIP switch information. This mode is not required during normal operation. Adjust plasma display. This mode is not required for normal operation. b) Test chart display This is a service mode. Use it to adjust plasma display settings. Notes: ¶ The plasma display need not be adjusted if it has already been set up. ¶ Use the supplied remote control to adjust the plasma display. For details, refer to the Operating Instructions. ¶ Press the [Esc] key or use the pen to click on the screen. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
33
4. Installing and Using Software
4.2.4
Test Mode
This is a service mode. Click
“
Test Mode
”
under
“
Hardware Information
”
in the CBdrvU task tray to open the screen
shown below.
a) State display
This screen shows results of hardware checks and the state of the driver and the operating system (Windows).
[Function overview]
Driver
Software Ver:
Indicate the version of the CBdrvU setup program
Pen Button (small):
Indicate the setting of the small pen button in the Property screen
Service Ver:
Indicate the version of the USB filter driver
Firmware Ver:
Indicate the version of the scan device firmware
System
Buttons:
●
: Correctly recognized
✻
: Not correctly recognized (during 3-button mouse emulation)
L:
Left mouse button
R:
Right mouse button
M:
Middle mouse button
Mouse pos:
Indicate mouse coordinates recognized by Windows
Angle:
Indicate currently set rotate angle
IP Address:
Indicate IP address of the connected PC
Computer Name:
Indicate the name of the connected PC
Service Mode:
Indicate scan device service information and DIP switch information.
This mode is not required during normal operation.
Test chart display:
Adjust plasma display. This mode is not required for normal operation.
b) Test chart display
This is a service mode. Use it to adjust plasma display settings.
Notes:
The plasma display need not be adjusted if it has already been set up.
Use the supplied remote control to adjust the plasma display. For details, refer to the Operating Instructions.
Press the [Esc] key or use the pen to click on the screen.