Pioneer FHD1 Owner's Manual - Page 18

Connecting the power cord

Get Pioneer FHD1 - PRO - 50inch Plasma Panel PDF manuals and user guides
UPC - 012562818733
View all Pioneer FHD1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

06 Preparation Connecting the power cord AC IN SPEAKER 8Ω ~16Ω + - L Power cord Noise filter Partially eliminates noise caused by the power source. CAUTION • Use only the supplied power cord. • Be sure to use the specified power supply voltage; neglecting this can result in fire or electric shock. • For the Plasma Display, a three-core power cord with a ground terminal is used for efficient protection. Always connect the power cord to a three-pronged outlet and make sure that the cord is properly grounded. NOTE • Always turn off the power of the Plasma Display when connecting or disconnecting power cords. • When not using this unit for extended periods, disconnect the power cord from its outlet. Connecting the speakers This unit is equipped with speaker output terminals. Consult the accompanying illustration when connecting your own speakers. 12 mm Twist exposed wire strands together. Push tab to the open position, and insert the wire. Then, close tab firmly to secure the wire in place. NOTE • When connecting speakers, be sure to connect the speaker's positive (+) and negative (-) terminals to the same terminals on this unit. Proper sound will not be produced if the (+) and (-) polarities are not connected correctly. • This unit supports the use of speakers with 8 Ω to 16 Ω impedance. 18 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
18
En
Preparation
06
Connecting the power cord
CAUTION
•
Use only the supplied power cord.
•
Be sure to use the specified power supply voltage;
neglecting this can result in fire or electric shock.
•
For the Plasma Display, a three-core power cord
with a ground terminal is used for efficient
protection. Always connect the power cord to a
three-pronged outlet and make sure that the cord
is properly grounded.
NOTE
• Always turn off the power of the Plasma Display when
connecting or disconnecting power cords.
• When not using this unit for extended periods, disconnect
the power cord from its outlet.
Connecting the speakers
This unit is equipped with speaker output terminals. Consult
the accompanying illustration when connecting your own
speakers.
NOTE
• When connecting speakers, be sure to connect the
speaker’s positive (+) and negative (–) terminals to the same
terminals on this unit. Proper sound will not be produced if
the (+) and (–) polarities are not connected correctly.
• This unit supports the use of speakers with 8
Ω
to 16
Ω
impedance.
AC IN
L
SPEAKER
8
Ω
~16
Ω
+
–
Power cord
Noise filter
Partially eliminates noise caused by the power source.
12 mm
Twist exposed wire
strands together.
Push tab to the open
position, and insert the
wire. Then, close tab firmly
to secure the wire in place.