Pioneer VSX 517-K Owner's Manual - Page 35

Additional information, Resetting the main unit

Get Pioneer VSX 517-K - AV Receiver PDF manuals and user guides
UPC - 012562849676
View all Pioneer VSX 517-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Additional information 09 English Deutsch Français Italiano Nederlands Español Problem Remedy No sound from subwoofer. • Make sure the subwoofer is switched on. • If the subwoofer has a volume knob, make sure it's turned up. • The Dolby Digital or DTS source you are listening to may not have an LFE channel. • Switch the subwoofer setting in Speaker setting on page 28 to YES or PLUS. • Switch the LFE Attenuator Setup on page 31 to LFEATT 0 or LFEATT 10. The PHASE CONTROL feature doesn't seem to have an audible effect. • If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the best overall effect on the sound). • Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 30). Noise during playback of a cassette deck. • Move the cassette deck further from your receiver, until the noise disappears. No sound is output or a noise • Set the digital volume level of the player to full, or to the neutral is output when software with position. DTS is played back. During a playback search, noise is output from a DTS compatible CD player. • This is not a malfunction, but be sure to turn the volume down to prevent the output of loud noise from your speakers. Can't operate the remote control. • Replace the batteries (refer to page 5). • Operate within 7 m (23 ft.), 30° of the remote sensor on the front panel (refer to page 5). • Remove the obstacle or operate from another position. • Avoid exposing the remote sensor on the front panel to direct light. The display is dark or off. • Press DIMMER on the remote repeatedly to return to the default. Resetting the main unit Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down the TONE button, press and hold the  STANDBY/ON button for about three seconds. 3 When you see RESET? appear in the display, press the ENTER button. OK? shows in the display. 4 Press SETUP to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. 35 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Additional information
09
35
En
English
Français
Deutsch
Nederlands
Italiano
Español
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1
Switch the receiver into standby.
2
While holding down the TONE button,
press and hold the
STANDBY/ON button
for about three seconds.
3
When you see RESET? appear in the
display, press the
ENTER
button.
OK?
shows in the display.
4
Press
SETUP
to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory default
settings.
No sound from subwoofer.
• Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have
an LFE channel.
• Switch the subwoofer setting in
Speaker setting
on page 28 to
YES
or
PLUS
.
• Switch the
LFE Attenuator Setup
on page 31 to
LFEATT 0
or
LFEATT 10
.
The
PHASE CONTROL
feature doesn’t seem to have
an audible effect.
• If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest frequency
setting. If there is a
PHASE
setting on your subwoofer, set it to 0º (or
depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers
(see
Speaker Distance
on page 30).
Noise during playback of a
cassette deck.
• Move the cassette deck further from your receiver, until the noise
disappears.
No sound is output or a noise
is output when software with
DTS is played back.
• Set the digital volume level of the player to full, or to the neutral
position.
During a playback search,
noise is output from a DTS
compatible CD player.
• This is not a malfunction, but be sure to turn the volume down to
prevent the output of loud noise from your speakers.
Can’t operate the remote
control.
• Replace the batteries (refer to page 5).
• Operate within 7 m (23 ft.), 30° of the remote sensor on the front
panel (refer to page 5).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off.
• Press
DIMMER
on the remote repeatedly to return to the default.
Problem
Remedy