Pioneer VSX-816-K Owner's Manual - Page 63

Additional information, Resetting the main unit, Switching the speaker, impedance

Get Pioneer VSX-816-K PDF manuals and user guides
UPC - 012562785851
View all Pioneer VSX-816-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

English Deutsch Français Italiano Nederlands Español Additional information 13 XM radio messages Symptom Cause Action Check Antenna The XM antenna is not connected. Check that the XM antenna cable is attached securely. XM ANT ERR A short-circuit occurring in the antenna or surrounding antenna cable. Make sure that there is nothing unusual with the antenna or antenna cable. Switch the power off then back on again. Updating The radio is being updated with the latest encryption code. Wait until the encryption code has been updated. Channels 00 and 01 should function normally. No Signal The XM signal is too weak at the current location. n/a Loading The receiver is acquiring audio or program information. Wait until the information has been received. Off Air The channel currently selected has stopped broadcasting. Select another channel. CH- - - You have selected a channel that does not exist, The receiver will automatically switch to channel or that you have not subscribed to. 001 (or the last selected channel). There is no artist name/feature, song/program title, or channel category associated with the channel at this time. No action needed. Resetting the main unit Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds. 3 When you see RESET? appear in the display, press ENTER. OK? shows in the display. 4 Press SETUP to confirm. OK appears in the display to indicate that the receiver has been reset to the factory settings. Switching the speaker impedance We recommend using speakers of 8Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6Ω impedance rating. • With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS button. Each time you do this, you switch between the impedance settings: • SP 6 OHM - Use this setting if your speakers are rated at 6Ω. • SP 8 OHM - Use this setting if your speakers are rated at 8Ω or more. 63 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Additional information
13
63
En
English
Français
Deutsch
Nederlands
Italiano
Español
XM radio messages
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1
Switch the receiver into standby.
2
While holding down the TONE button,
press and hold the
±
STANDBY/ON button for
about three seconds.
3
When you see RESET? appear in the
display, press
ENTER
.
OK?
shows in the display.
4
Press
SETUP
to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory settings.
Switching the speaker
impedance
We recommend using speakers of 8
Ω
with this
system, but it is possible to switch the
impedance setting if you plan to use speakers
with a 6
Ω
impedance rating.
•
With the receiver in standby, press
±
STANDBY/ON
while holding down the
SPEAKERS
button.
Each time you do this, you switch between the
impedance settings:
•
SP 6 OHM
– Use this setting if your
speakers are rated at 6
Ω
.
•
SP 8 OHM
– Use this setting if your
speakers are rated at 8
Ω
or more.
Symptom
Cause
Action
Check Antenna
The XM antenna is not connected.
Check that the XM antenna cable is attached
securely.
XM ANT ERR
A short-circuit occurring in the antenna or
surrounding antenna cable.
Make sure that there is nothing unusual with the
antenna or antenna cable. Switch the power off
then back on again.
Updating
The radio is being updated with the latest
encryption code.
Wait until the encryption code has been
updated. Channels 00 and 01 should function
normally.
No Signal
The XM signal is too weak at the current location.
n/a
Loading
The receiver is acquiring audio or program
information.
Wait until the information has been received.
Off Air
The channel currently selected has stopped
broadcasting.
Select another channel.
CH– – –
You have selected a channel that does not exist,
or that you have not subscribed to.
The receiver will automatically switch to channel
001 (or the last selected channel).
– – – – – – – –
There is no artist name/feature, song/program
title, or channel category associated with the
channel at this time.
No action needed.