Pioneer VSX-90TXV Owner's Manual - Page 57

Other Settings 09 • MAX - Dynamic range is reduced (loud sounds are reduced in volume while quieter sounds are increased). 3 When you're finished, press RETURN. You return to the Other Setup menu. Dual Mono Setup • Default setting: CH1 You can specify how dual mono encoded Dolby Digital and DTS soundtracks should be played. Dual mono is not widely used, but is sometimes necessary when two languages need to be sent to separate channels. 1 Select 'Dual Mono Setup' from the Other Setup menu. 6.Other Setup a.DRC Setup b.Dual Mono Setup c.LFE ATT Setup d.SR+ Setup e.Video Conv. Setup f. Multi Zone Setup g.12V Trigger Setup :Return 6b.Dual Mono Setup Dual Mono [ CH1 :Finish 2 Choose the setting that you want. • CH1 - Only channel 1 is played • CH2 - Only channel 2 is played • CH1 CH2 - Both channels are played through the front speakers 3 When you're finished, press RETURN. You return to the Other Setup menu. LFE Attenuator Setup • Default setting: ATT 0dB Some Dolby Digital and DTS audio sources include ultralow bass tones. Set the LFE attenuator as necessary to prevent the ultra-low bass tones from distorting the sound from the speakers. 1 Select 'LFE ATT Setup' from the Other Setup menu. 6.Other Setup a.DRC Setup b.Dual Mono Setup c.LFE ATT Setup d.SR+ Setup e.Video Conv. Setup f. Multi Zone Setup g.12V Trigger Setup :Return 6c. LFE ATT Setup LFE ATT ATT 0dB :Finish 2 Choose the setting that you want. • ATT 0dB - No limiting (recommended) • ATT 10dB - 10 dB of limiting • LFE OFF - No sound from LFE channel 3 When you're finished, press RETURN. You return to the Other Setup menu. SR+ Setup for Pioneer plasma displays • Default setting: OFF (all settings) Make the following settings if you have connected a Pioneer plasma display to this receiver using an SR+ cable. Note that the number of settings available will depend on the plasma display you've connected. See also Using this receiver with a Pioneer plasma display on page 53. 1 Select 'SR+ Setup' from the Other Setup menu. 6.Other Setup a.DRC Setup b.Dual Mono Setup c.LFE ATT Setup d.SR+ Setup e.Video Conv. Setup f. Multi Zone Setup g.12V Trigger Setup :Return 6d.SR+ Setup PDP Volume Control OFF PDP Input Select DVD/LD [ OFF ] TV/SAT [ OFF ] DVR 1 [ OFF ] DVR 2 [ OFF ] VIDEO [ OFF ] Monitor Out [ OFF ] :Finish 2 Select the 'PDP Volume Control' setting you want. • OFF - The receiver does not control the volume of the plasma display • ON - When the receiver is switched to one of the inputs that use the plasma display (DVD/LD, or another function below), the volume on the plasma display is muted so only sound from the receiver is heard. 3 Assign any input source connected to the plasma display to the corresponding input number. This matches the receiver's input source with a numbered video input on the plasma display. For example, assign DVD/LD to input-2 if you have connected your DVD video output to video input 2 on the plasma display. • The Monitor Out should be set to the input that you've used to connect this receiver to your plasma display. 6d.SR+ Setup PDP Volume Control [ ON ] PDP Input Select DVD/LD OFF T V / S AT [ OFF ] DVR 1 DVR 2 [ OFF ] [ OFF ] VIDEO Monitor Out [ OFF ] [ OFF ] :Finish 6d.SR+ Setup PDP Volume Control [ ON ] PDP Input Select DVD/LD input-2 T V / S AT [ OFF ] DVR 1 DVR 2 [ OFF ] [ OFF ] VIDEO Monitor Out [ OFF ] [ OFF ] :Finish 4 When you're finished, press RETURN. You return to the Other Setup menu. Video Converter Setup • Default setting: ON The video converter allows you to see analog video sources through all of this receiver's MONITOR VIDEO OUT jacks. Note that the converter gives priority to component, S-video, then composite (in that order). See About the video converter on page 12 for more on this. 57 En