Pioneer VSX-LX305 Elite 9.2-Channel Network AV Receiver Instruction Manual Eng - Page 115

Speaker Impedance Default Value: 6 ohms or above, Height 2 Speaker Default Value: Rear High

Get Pioneer VSX-LX305 Elite 9.2-Channel Network AV Receiver PDF manuals and user guides View all Pioneer VSX-LX305 Elite 9.2-Channel Network AV Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

Speaker ‰‰Height 2 Speaker (Default Value: Rear High) Set the speaker type if height speakers are connected to the HEIGHT 2 terminals. Select "Front High", "Top Front", "Top Middle", "Top Rear", "Rear High", "Dolby Speaker (Front)" or "Dolby Speaker (Surr)" according to the type and layout of the connected speakers. However, the options selectable for the "Height 1 Speaker" are as follows. If "Height 1 Speaker" is set to "Front High": Select from "Top Middle", "Top Rear", "Rear High" or "Dolby Speaker (Surr)". If "Height 1 Speaker" is set to "Top Front" or "Dolby Speaker (Front)": Select from "Top Rear", "Rear High" or "Dolby Speaker (Surr)". If "Height 1 Speaker" is set to "Top Middle": Fixed to "Rear High". • "Dolby Speaker (Surr)" can only be selected when surround speakers are being used. You can check speakers that you are using on the figure displayed in "Speaker Channels". • If an item cannot be selected even though connection is correct, check that the settings in "Speaker Channels" matches the number of connected channels. ‰‰Zone Speaker (Default Value: No) Set whether speakers are connected to ZONE 2 or ZONE 3 speaker terminals. • This setting cannot be selected when "Zone 2 Preout" is set to "Zone B". Zone 2 When speakers are connected to ZONE 2 speaker terminals Zone 2/Zone 3 When connecting speaker to both ZONE 2 speaker terminal and ZONE 3 speaker terminals. • This setting cannot be selected under any of following conditions. -- When the surround back speakers are used -- When the height speakers are used No When speakers are not connected to neither ZONE 2 nor ZONE 3 speaker terminals Setup ‰‰Zone 2 Preout (Default Value: Zone 2) Set an output destination of the audio output from ZONE 2 PRE/LINE OUT or ZONE B LINE OUT jack. • This setting is fixed to "Zone 2" when "Zone Speaker" is set to "Zone 2" or "Zone 2/Zone 3". Zone 2 Zone B When connecting an integrated amplifier in a separate room (ZONE 2) When connecting an integrated amplifier, transmitter of wireless headphones, etc. to ZONE B ‰‰Bi-Amp (Default Value: No) Set whether the front speakers are bi-amp connected. No When front speakers are not bi-amp connected Yes When front speakers are bi-amp connected • This setting will be set to "No" in either of following cases. -- When 2 sets of height speakers are used -- When surround back speakers and height speakers are being used at the same time -- When "Zone Speaker" is set to "Zone 2" or "Zone 2/Zone 3" ‰‰Speaker Impedance (Default Value: 6 ohms or above) Set the impedance (Ω) of the connected speakers. • For impedance, check the indications on the back of the speakers or their instruction manual. 4ohms 6 ohms or above When any of the connected speakers have 4 Ω or more to less than 6 Ω impedance When the connected speakers all have 6 Ω or more impedance 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
115
Setup
Speaker
±
Height 2 Speaker (Default Value: Rear High)
Set the speaker type if height speakers are connected to the HEIGHT 2
terminals. Select "Front High", "Top Front", "Top Middle", "Top Rear", "Rear
High", "Dolby Speaker (Front)" or "Dolby Speaker (Surr)" according to the type
and layout of the connected speakers. However, the options selectable for the
"Height 1 Speaker" are as follows.
If "Height 1 Speaker" is set to "Front High": Select from "Top Middle", "Top
Rear", "Rear High" or "Dolby Speaker (Surr)".
If "Height 1 Speaker" is set to "Top Front" or "Dolby Speaker (Front)": Select
from "Top Rear", "Rear High" or "Dolby Speaker (Surr)".
If "Height 1 Speaker" is set to "Top Middle": Fixed to "Rear High".
•
"Dolby Speaker (Surr)" can only be selected when surround speakers
are being used. You can check speakers that you are using on the figure
displayed in "Speaker Channels".
•
If an item cannot be selected even though connection is correct, check
that the settings in "Speaker Channels" matches the number of connected
channels.
±
Zone Speaker (Default Value: No)
Set whether speakers are connected to ZONE 2 or ZONE 3 speaker terminals.
•
This setting cannot be selected when "Zone 2 Preout" is set to "Zone B".
Zone 2
When speakers are connected to ZONE 2 speaker terminals
Zone 2/Zone 3
When connecting speaker to both ZONE 2 speaker terminal
and ZONE 3 speaker terminals.
•
This setting cannot be selected under any of following
conditions.
– When the surround back speakers are used
– When the height speakers are used
No
When speakers are not connected to neither ZONE 2 nor
ZONE 3 speaker terminals
±
Zone 2 Preout (Default Value: Zone 2)
Set an output destination of the audio output from ZONE 2 PRE/LINE OUT or
ZONE B LINE OUT jack.
• This setting is fixed to "Zone 2" when "Zone Speaker" is set to "Zone 2" or
"Zone 2/Zone 3".
Zone 2
When connecting an integrated amplifier in a separate room
(ZONE 2)
Zone B
When connecting an integrated amplifier, transmitter of
wireless headphones, etc. to ZONE B
±
Bi-Amp (Default Value: No)
Set whether the front speakers are bi-amp connected.
No
When front speakers are not bi-amp connected
Yes
When front speakers are bi-amp connected
•
This setting will be set to "No" in either of following cases.
– When 2 sets of height speakers are used
– When surround back speakers and height speakers are
being used at the same time
–
When "Zone Speaker" is set to "Zone 2" or "Zone 2/Zone 3"
±
Speaker Impedance (Default Value: 6 ohms or above)
Set the impedance (Ω) of the connected speakers.
•
For impedance, check the indications on the back of the speakers or their
instruction manual.
4ohms
When any of the connected speakers have 4 Ω or more to less
than 6 Ω impedance
6 ohms or
above
When the connected speakers all have 6 Ω or more
impedance