Poulan PP16H44A User Manual - Page 27

Cause, Correction

Get Poulan PP16H44A PDF manuals and user guides View all Poulan PP16H44A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

TROUBLESHOOTING POINTS 3LEM CAUSE continues to run )perator leaves seat tachment clutch ad 1. Faulty operator-safety presence control system. emomr....marsaostamum ut - uneven 1. Worn, bent or loose blade. 2. Mower deck not level. 3. Buildup of grass, leaves, and trash under mower. 4. Bent blade mandrel. CORRECTION f. Check wiring, switches and connections. If not corrected, contact an authorized service center. 1. Replace blade. Tighten blade bolt. 2. Level mower deck. 3. Clean underside of mower housing. 4. Replace blade mandrel. blades will not 1. Obstruction in clutch mechanism. 2. Mower drive belt out of adjustment. 3. Wom/damaged mower drive belt. 4. Frozen idler pulley. 5. Frozen blade mandrel. 1. Remove obstruction. 2. Adjust mower drive belt. 3. Replace mower drive belt. 4. Replace idler pulley. 5. Replace blade mandrel. .ass discharge 1. Engine speed too slow. 2. Travel speed too fast. 3. Wet grass. 4. Mower deck not level. 5. Low/uneven tire air pressure. 6. Worn, bent or loose blade. 7. Buildup of grass, leaves and trash under mower. 8. Mower drive belt worn or out of adjustment. 9. Blades improperly installed. 10, Improper blades used. 1. Place throttle control in "FAST" position. 2. Shift to slower speed. 3. Allow grass to dry before mowing. 4. Level mower deck. 5. Check tires for proper air pressure. 8. Replace/sharpen blade. Tighten blade bolt. 7. Clean underside of mower housing. 8. Replace/adjust mower drive belt. 9. Reinstall blades sharp edge down. 10. Replace with blades listed in ti-is manual. Iht(s) not working luipped) 1. Switch is "OFF". 2. Bulb(s) burned out. 3. Faulty light switch. 4. Loose or damaged wiring. 5. Blown fuse. 1. Turn switch "ON". 2. Replace bulb(s). 3. Check/replace light switch. 4. Check wiring and connections. 5. Replace fuse. will not charge 1. Bad battery cell(s). 2. Poor cable connections. 3. Faulty regulator (if so equipped). 4. Faulty alternator. 1. Replace battery. 2. Check/dean all connections. 3. Replace regulator. 4. Replace alternator. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
TROUBLESHOOTING
POINTS
3LEM
CAUSE
CORRECTION
continues
to
run
)perator
leaves
seat
tachment
clutch
ad
1.
Faulty
operator
-safety
presence
control
system.
f.
Check
wiring,
switches
and
connections.
If
not
corrected,
contact
an
authorized
service
center.
emomr
....
marsaostamum
ut
-
uneven
1.
Worn,
bent
or
loose
blade.
1.
Replace
blade.
Tighten
blade
bolt.
2.
Mower
deck
not
level.
2.
Level
mower
deck.
3.
Buildup
of
grass,
leaves,
and
trash
under
mower.
3.
Clean
underside
of
mower
housing.
4.
Bent
blade
mandrel.
4.
Replace
blade
mandrel.
blades
will
not
1.
Obstruction
in
clutch
mechanism.
1.
Remove
obstruction.
2.
Mower
drive
belt
out
of
adjustment.
2.
Adjust
mower
drive
belt.
3.
Wom/damaged
mower
drive
belt.
3.
Replace
mower
drive
belt.
4.
Frozen
idler
pulley.
4.
Replace
idler
pulley.
5.
Frozen
blade
mandrel.
5.
Replace
blade
mandrel.
.ass
discharge
1.
Engine
speed
too
slow.
1.
Place
throttle
control
in
"FAST"
position.
2.
Travel
speed
too
fast.
2.
Shift
to
slower
speed.
3.
Wet
grass.
3.
Allow
grass
to
dry
before
mowing.
4.
Mower
deck
not
level.
4.
Level
mower
deck.
5.
Low/uneven
tire
air
pressure.
5.
Check
tires
for
proper
air
pressure.
6.
Worn,
bent
or
loose
blade.
8.
Replace/sharpen
blade.
Tighten
blade
bolt.
7.
Buildup
of
grass,
leaves
and
trash
under
mower.
7.
Clean
underside
of
mower
housing.
8.
Mower
drive
belt
worn
or
out
of
adjustment.
8.
Replace/adjust
mower
drive
belt.
9.
Blades
improperly
installed.
9.
Reinstall
blades
sharp
edge
down.
10,
Improper
blades
used.
10.
Replace
with
blades
listed
in
ti
-
is
manual.
Iht(s)
not
working
1.
Switch
is
"OFF".
1.
Turn
switch
"ON".
luipped)
2.
Bulb(s)
burned
out.
2.
Replace
bulb(s).
3.
Faulty
light
switch.
3.
Check/replace
light
switch.
4.
Loose
or
damaged
wiring.
4.
Check
wiring
and
connections.
5.
Blown
fuse.
5.
Replace
fuse.
will
not
charge
1.
Bad
battery
cell(s).
1.
Replace
battery.
2.
Poor
cable
connections.
2.
Check/dean
all
connections.
3.
Faulty
regulator
(if
so
equipped).
3.
Replace
regulator.
4.
Faulty
alternator.
4.
Replace
alternator.
27