Poulan PP16H44A User Manual - Page 7

Assembly

Get Poulan PP16H44A PDF manuals and user guides View all Poulan PP16H44A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

ASSEMBLY DLS REQUIRED FOR ASSEMBLY ;ket wrench set will make assembly easier. Standard ch sizes are listed. /16" wrenches (1) Tire pressure gauge 44" wrench (1) Screwdriver /2" wrench (1) Utility Knife n right and left hand is mentioned in this manual, it is when you are in the operating position (seated id the steering wheel). REMOVE UNIT FROM CARTON 'ACK CARTON Remove all accessible loose parts and parts cartons rom carton (See page 6). 3ut along dotted lines on the carton, from top to bottom, III four corners of carton and lay panels flat. Remove mower deck from skid. :,heck for any additional. loose parts or cartons and emove. FORE ROLLING UNIT OFF SKID 'ACH STEERING WHEEL (See Fig. 1) Remove hex locknut and large flat washer from steerng shaft. osition front wheels of the tractor so they are pointing straight forward. osition steering wheel so cross bars are horizontal left to right) and slide onto adapter. Secure steering wheel to steering shaft with hex locklift and large flat washer previously removed. Tighten Securely. ;nap insert into center of steering wheel. Remove protective plastic from tractor hood and grill. )RTANT: CHECK FOR AND REMOVE ANY STAPLES KID THAT MAY PUNCTURE TIRES WHERE UNIT IS LOLL OFF SKID. e Fig. 2) Raise attachment lift lever to its highest position. Release parking brake by depressing clutch/brake 3edal. lace motion control lever in "NEUTRAL" position. Move freewheel control to freewheeling position. Roll unit backwards off skid. STEERING WHEEL ,/ INSERT HEX LOCKNUT------------40 FLAT WASHER STEERING WHEEL STEERING WHEEL ADAPTER STEERING SHAFT FIG. 1 CLUTCH/BRAKE PEDAL LIFT LEVER FREEWHEEL CONTROL PARKING BRAKE FIG. 2 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
ASSEMBLY
DLS
REQUIRED
FOR
ASSEMBLY
;ket
wrench
set
will
make
assembly
easier.
Standard
ch
sizes
are
listed.
/16"
wrenches
(1)
Tire
pressure
gauge
44"
wrench
(1)
Screwdriver
/2"
wrench
(1)
Utility
Knife
n
right
and
left
hand
is
mentioned
in
this
manual,
it
is
when
you
are
in
the
operating
position
(seated
id
the
steering
wheel).
REMOVE
UNIT
FROM
CARTON
'ACK
CARTON
Remove
all
accessible
loose
parts
and
parts
cartons
rom
carton
(See
page
6).
3ut
along
dotted
lines
on
the
carton,
from
top
to
bottom,
III
four
corners
of
carton
and
lay
panels
flat.
Remove
mower
deck
from
skid.
:,heck
for
any
additional.
loose
parts
or
cartons
and
emove.
FORE
ROLLING
UNIT
OFF
SKID
'ACH
STEERING
WHEEL
(See
Fig.
1)
Remove
hex
locknut
and
large
flat
washer
from
steer-
ng
shaft.
osition
front
wheels
of
the
tractor
so
they
are
pointing
straight
forward.
osition
steering
wheel
so
cross
bars
are
horizontal
left
to
right)
and
slide
onto
adapter.
Secure
steering
wheel
to
steering
shaft
with
hex
lock
-
lift
and
large
flat
washer
previously
removed.
Tighten
Securely.
;nap
insert
into
center
of
steering
wheel.
Remove
protective
plastic
from
tractor
hood
and
grill.
)RTANT:
CHECK
FOR
AND
REMOVE
ANY
STAPLES
KID
THAT
MAY
PUNCTURE
TIRES
WHERE
UNIT
IS
LOLL
OFF
SKID.
e
Fig.
2)
Raise
attachment
lift
lever
to
its
highest
position.
Release
parking
brake
by
depressing
clutch/brake
3edal.
lace
motion
control
lever
in
"NEUTRAL"
position.
Move
freewheel
control
to
freewheeling position.
Roll
unit
backwards
off
skid.
STEERING
WHEEL
INSERT
,/
HEX
LOCKNUT------------40
FLAT
WASHER
STEERING
WHEEL
STEERING
WHEEL
ADAPTER
STEERING
SHAFT
FIG.
1
CLUTCH/BRAKE
PEDAL
LIFT
LEVER
FREEWHEEL
CONTROL
PARKING
BRAKE
FIG.
2
7