Poulan XC1182B User Manual - Page 22

Replace, Motion, Drive, Transaxle, Shifter, Linkage, Adjustment, Figs., Adjust, Steering, Wheel,

Get Poulan XC1182B PDF manuals and user guides View all Poulan XC1182B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See FIG. 32) TRANSAXLE SHIFTER LINKAGE AND ADJUSTMENT (See FIGS. 33 and 34) Park the tractor on level surface. Engage parking brake. For ease of service there is a belt installation guide decal on bottom side of left footrest. • Remove mower (See "TO REMOVE MOWER" in this section of this manual). • Remove the clutch locator. • Loosen bolt securing R.H. belt keeper. • Disconnect clutch wire harness. • Pull belt off clutching idler and raise to top side of pulley. • Release parking brake. Push belt over and away from clutching idler. • Pull belt slack toward rear of tractor. Remove belt from transmission pulley by deflecting keepers to force belt up and out of pulley. Use belt to push keepers away from pulley. • Work belt around remaining pulleys and keepers, working toward transaxle pulley. • Pull belt forward off of transaxle pulley and down over electric clutch. • Install new belt by reversing above procedure. IMPORTANT: MAKE SURE RIGHT HAND BELT KEEP- ER IS POSITIONED CORRECTLY BETWEEN LOCATOR TABS, AND ELEC- TRIC CLUTCH CONNECTION IS SECURE. 7AME CLUTCH WIRE CONNECTOR The transaxle should be in neutral when the gear shift lever is in the neutral (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows. • Make sure transaxle is in neutral. • Loosen two locknuts on tie rod. GEAR SHIFT LEVER N UTRAL LOCK GATE .:, as 1 FIG. 33 • Turn center rod until gearshift lever falls into neutral lock gate on fender console. L • CK NUTS REAR OF TRACTOR .0. R.H. BELT KEEPER TRANSAXLE PULLEY CLUTCHING IDLER ELECTRIC CLUTCH 0 0 CLUTCH LOCATOR FIG. 32 CENTER ROD TIE ROD 0 % TR NSAXLE 0 FIG. 34 • Tighten locknuts securely. TO ADJUST STEERING WHEEL ALIGNMENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly section of this manual. FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjustable on your unit. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
SERVICE
AND
ADJUSTMENTS
TO
REPLACE
MOTION
DRIVE
BELT
(See
FIG.
32)
Park
the
tractor
on
level
surface.
Engage
parking
brake.
For
ease
of
service
there
is
a
belt
installation
guide
decal
on
bot-
tom
side
of
left
footrest.
•
Remove
mower
(See
"TO
REMOVE
MOWER"
in
this
sec-
tion
of
this
manual).
•
Remove
the
clutch
locator.
•
Loosen
bolt
securing
R.H.
belt
keeper.
•
Disconnect
clutch
wire
harness.
•
Pull
belt
off
clutching
idler
and
raise
to
top
side
of
pulley.
•
Release
parking
brake.
Push
belt
over
and
away
from
clutching
idler.
•
Pull
belt
slack
toward
rear
of
tractor.
Remove
belt
from
transmission
pulley
by
deflecting
keepers
to
force
belt
up
and
out
of
pulley.
Use
belt
to
push
keepers
away
from
pul-
ley.
•
Work
belt
around
remaining
pulleys
and
keepers,
working
toward
transaxle
pulley.
•
Pull
belt
forward
off
of
transaxle
pulley
and
down
over
electric
clutch.
•
Install
new
belt
by
reversing
above
procedure.
IMPORTANT:
MAKE
SURE
RIGHT
HAND
BELT
KEEP-
ER
IS
POSITIONED
CORRECTLY
BE-
TWEEN
LOCATOR
TABS,
AND
ELEC-
TRIC
CLUTCH
CONNECTION
IS
SE-
CURE.
REAR
OF
TRACTOR
R.H.
BELT
KEEPER
CLUTCHING
IDLER
TRANSAXLE
PULLEY
ELECTRIC
CLUTCH
7AME
0
CLUTCH
LOCATOR
.0.
0
CLUTCH
WIRE
CONNECTOR
FIG.
32
TRANSAXLE
SHIFTER
LINKAGE
AND
ADJUSTMENT
(See
FIGS.
33
and
34)
The
transaxle
should
be
in
neutral
when
the
gear
shift
lever
is
in
the
neutral
(lock
gate)
position.
The
adjustment
is
preset
at
the
factory;
however,
if
adjustment
is
needed,
proceed
as
follows.
•
Make
sure
transaxle
is
in
neutral.
•
Loosen
two
locknuts
on
tie
rod.
GEAR
SHIFT
LEVER
.:,
N
UTRAL
LOCK
GATE
a s
1
FIG.
33
•
Turn
center
rod
until
gearshift
lever
falls
into
neutral
lock
gate
on
fender
console.
TIE
ROD
0
L
•
CK
NUTS
CENTER
ROD
%
0
TR
NSAXLE
FIG.
34
•
Tighten
locknuts
securely.
TO
ADJUST
STEERING
WHEEL
ALIGNMENT
If
steering
wheel
crossbars
are
not
horizontal
(left
to
right)
when
wheels
are
positioned
straight
forward,
remove
steer-
ing
wheel
and
reassemble
per
instructions
in
the
Assembly
section
of
this
manual.
FRONT
WHEEL
TOE-IN/CAMBER
The
front
wheel
toe
—in
and
camber
are
not
adjustable
on
your
unit.
If
damage
has
occurred
to
affect
the
front
wheel
toe
—in
or
camber,
contact
your
nearest
authorized
service
center.