ProForm Performance 1250 Treadmill Uk Manual - Page 27

The Power Cord.

Get ProForm Performance 1250 Treadmill PDF manuals and user guides View all ProForm Performance 1250 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Locate the Reed Switch (52) and the Magnet (50) on the left side of the Pulley (49). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Tek Screw (14), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown) and run the treadmill for a few minutes to check for a correct speed reading. Top View 52 49 14 50 1/8 in. b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b 2-3 in. Idler Roller Screws SYMPTOM: The incline of the treadmill does not change correctly a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system. SYMPTOM: The walking belt slows when walked on a. If an extension cord is needed, use only a 3-conductor, 14-gauge (1 mm2) cord that is no longer than 5 ft. (1.5 m). c. Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform unless instructed to do so by an authorized service representative. Such substances may deteriorate the walking belt and cause excessive wear. If you suspect the walking belt needs more lubricant, see the front cover of this manual. d. If the walking belt still slows when walked on, see the front cover of this manual. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
27
Locate the Reed Switch (52) and the Magnet (50)
on the left side of the Pulley (49). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet
and the Reed Switch is about 1/8 in. (3 mm).
If
necessary, loosen the #8 x 3/4" Tek Screw (14),
move the Reed Switch slightly, and then retighten
the Screw. Reattach the Motor Hood (not shown)
and run the treadmill for a few minutes to check for
a correct speed reading.
SYMPTOM: The incline of the treadmill does not
change correctly
a.
With the key in the console, press one of the
Incline buttons.
While the incline is changing, re-
move the key.
After a few seconds, reinsert the
key. The treadmill will automatically rise to the
maximum incline level and then return to the mini-
mum level. This will recalibrate the incline system.
SYMPTOM: The walking belt slows when walked on
a.
If an extension cord is needed, use only a 3-con-
ductor, 14-gauge (1 mm
2
) cord that is no longer
than 5 ft. (1.5 m).
b.
If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be-
come damaged. Remove the key and
UNPLUG
THE POWER CORD.
Using the hex key, turn both
idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
c.
Your treadmill features a walking belt coated with
high-performance lubricant.
IMPORTANT: Never
apply silicone spray or other substances to the
walking belt or the walking platform unless in-
structed to do so by an authorized service rep-
resentative. Such substances may deteriorate
the walking belt and cause excessive wear.
If
you suspect the walking belt needs more lubricant,
see the front cover of this manual.
d.
If the walking belt still slows when walked on, see
the front cover of this manual.
50
14
52
1/8 in.
49
Idler Roller Screws
2–3 in.
b
Top
View