ProForm Xp 300 Weight Bench Exerciser English Manual - Page 13

the Pulley, a Cable Trap 66, and two Half Finger

Get ProForm Xp 300 Weight Bench Exerciser PDF manuals and user guides View all ProForm Xp 300 Weight Bench Exerciser manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

24. Route the Cable (61) under a Pulley (63). Attach 24 the Pulley, a Cable Trap (66), and two Half Finger Guards (65) to the two Pulley Plates (35) with an M10 x 50mm Bolt (79) and an M10 Nylon Locknut (77). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 25. Route the Cable (61) over a Pulley (63). Attach 25 the Pulley inside the Top Frame (45) with an M10 x 78mm Bolt (87) and an M10 Nylon Locknut (77). 26. Attach the Cable (61) to the M10 x 20mm Bolt 26 (89) with an M10 Nylon Locknut (77). Make sure that the Cable can pivot easily on the Bolt. 77 65 35 61 63 66 35 65 79 45 77 87 63 61 61 77 89 27. Route the second Cable (61) under a Pulley (63). 27 Attach the Pulley to the Center Rack Base (39) with an M10 x 45mm Bolt (75) and an M10 Nylon Locknut (77). 77 63 61 75 39 28. Route the Cable (61) over a Pulley (63). Attach 28 the Pulley, a Cable Trap (66), and two Half Finger Guards (65) to the two Pulley Plates (35) at the indicated hole with an M10 x 50mm Bolt (79) and an M10 Nylon Locknut (77). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 13 77 65 66 35 65 79 63 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
13
24. Route the Cable (61) under a Pulley (63). Attach
the Pulley, a Cable Trap (66), and two Half Finger
Guards (65) to the two Pulley Plates (35) with an
M10 x 50mm Bolt (79) and an M10 Nylon Locknut
(77).
Make sure that the Cable Trap is oriented
to hold the Cable in the groove of the Pulley.
25. Route the Cable (61) over a Pulley (63). Attach
the Pulley inside the Top Frame (45) with an M10
x 78mm Bolt (87) and an M10 Nylon Locknut
(77).
26. Attach the Cable (61) to the M10 x 20mm Bolt
(89) with an M10 Nylon Locknut (77).
Make sure
that the Cable can pivot easily on the Bolt.
27. Route the second Cable (61) under a Pulley (63).
Attach the Pulley to the Center Rack Base (39)
with an M10 x 45mm Bolt (75) and an M10 Nylon
Locknut (77).
77
65
65
79
35
35
66
63
61
24
25
77
87
45
63
61
27
28
89
61
77
26
61
63
75
39
77
61
79
65
35
63
66
77
65
28. Route the Cable (61) over a Pulley (63). Attach
the Pulley, a Cable Trap (66), and two Half Finger
Guards (65) to the two Pulley Plates (35) at the
indicated hole with an M10 x 50mm Bolt (79) and
an M10 Nylon Locknut (77).
Make sure that the
Cable Trap is oriented to hold the Cable in the
groove of the Pulley.