Rane AC 23S Operation Manual - Page 11
Rear Panel: Alternate Mono 4-way Connections
View all Rane AC 23S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
REAR PANEL: ALTERNATE MONO 4-WAY CONNECTIONS Mono 4-way connection labels are in this row 8 79 8 1 Input 100-240 V COMMERCIAL AUDIO 50/60 Hz 7 WATTS EQUIPMENT 24TJ AC 23S MADE IN U.S.A. RANE CORP. PIN 2: POSITIVE PIN 3: NEGATIVE PIN 1: CHASSIS GND HIGH OUT 3W: MID OUT 2W: LOW 3W: LOW OUT 2W: OMIT R ACN 001 345 482 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. HIGH OUT 4W: OMIT 5W: HIGH MID OUT LOW OUT CHANNEL 2 IN MONO: OMIT STEREO 3W / 2W SET TO 5W CHANNEL 2 STEREO 3W 2W STEREO MONO CHANNEL 1 STEREO 4W 5W 3W 2W MONO: SET SWITCHES AS SHOWN HIGH OUT 3W: MID OUT 3W: LOW OUT 2W: LOW 2W: OMIT MONO: OMIT MID OUT SUB OUT CHANNEL 1 IN MONO 4W / 5W IN 0 65 2 Patch Cable 43 High Amp Low Amp Mid Amp Sub Amp The switching in the AC 23S will result in a Mono 4‑Way configuration with the crossover ranges SUB, LOW, MID & HIGH from left to right across the bottom front panel. By connecting a patch cable from the CHANNEL 1 HIGH OUT to the CHANNEL 2 INPUT, the LOW / MID crossover range changes from 70 Hz‑1 kHz to a higher range of 190 Hz‑7 kHz. Set the CHANNEL 1 HIGH LEVEL and the CHANNEL 2 MASTER LEVEL controls to "7" for unity gain. Switch CHANNEL 1 to 3‑Way, CHANNEL 2 to 2‑Way, and set the MONO switch to 5‑Way. 1 MONO INPUT: Connect the output from your mixer or other signal source only to the MONO 4W / 5W INPUT; do not use the Channel 2 Input. Pin 2 is "hot" per AES standards. 2 Patch cable: For this alternate Mono 4-Way installation, connect a balanced patch cord from the CHANNEL 1 HIGH OUT to the CHANNEL 2 INPUT as shown. 3 SUBWOOFER OUTPUT: Connect the SUB OUT to the input of the subwoofer amplifier (or bass bin amp). 4 LOW OUTPUT: Connect the MID OUT to the input of the low frequency amplifier. 5 MID OUTPUT: Connect the HIGH-MID OUT to the input of the mid frequency amplifier. 6 HlGH OUTPUT: Connect the HIGH OUT to the input of the high frequency amplifier. 7 STEREO‑MONO switch: Be sure this switch is in the STEREO out position. Yes, STEREO. A Mono circuit is created when Channel 1 is patched into Channel 2, and the correct signal flow depends on this switch. 8 STEREO 2‑WAY / 3‑WAY switches: For this configuration, set CHANNEL 1 to 3-Way, and CHANNEL 2 to 2-Way. 9 MONO 4‑Way / 5‑Way switch: Be sure this switch is is in the 5-Way position. Yes, 5-Way. Just do it if you want this to work. 0 Universal Voltage Input: via a miniature IEC 60320 C6 appliance inlet. This mates with an IEC 60320 C5 line cord (USA domestic). Do not lift the ground connection! Manual-8