Rane AC 23S Operation Manual - Page 7

FRONT PANEL: STEREO 3-WAY CONFIGURATION Stereo 3-way control labels are in this row CH 1 MASTER LEVEL 46 2 8 0 10 LOW 2W: INACTIVE LEVEL 46 MUTE DELAY 46 2 8 2 8 0 10 MIN MAX LOW / MID MID 2W: INACTIVE 2W: LOW FREQUENCY 240 400 LEVEL DELAY 200 600 MUTE 150 750 4 6 46 100 850 80 900 2 8 2 8 70 1k 0 10 MIN MAX MID / HIGH 2W: LOW / HIGH FREQUENCY 700 1.0k 550 2.0k 475 2.8k 350 4.5k 250 5.8k 190 7.0k HIGH LEVEL 46 2 8 0 10 CH 2 MASTER LEVEL 46 2 8 0 10 MONO MASTER SUBWOOFER SUB / LOW MID 4W: MID / HIGH 5W: MID / HIGH-MID MONO 4W OR 5W: INACTIVE LOW 2W: INACTIVE LEVEL 46 MUTE DELAY 46 2 8 2 8 LOW / MID MID 2W: INACTIVE 2W: LOW FREQUENCY 240 400 LEVEL DELAY 200 600 MUTE 150 750 4 6 46 100 850 80 900 2 8 2 8 70 1k MID / HIGH 2W: LOW / HIGH FREQUENCY 700 1.0k 550 2.0k 475 2.8k 350 4.5k 250 5.8k 190 7.0k HIGH LEVEL 46 2 8 0 10 MIN MAX 0 10 MIN MAX 0 10 LOW LOW / MID 4W: INACTIVE 5W: HIGH-MID 4W: INACTIVE 5W: HIGH-MID / HIGH HIGH POWER AC 23S ACTIVE CROSSOVER 1 345 6 789 0 q 2 345 6 789 0 q w Observe the labels screened above the controls for stereo operation. 1 Channel 1 MASTER LEVEL control: Sets the overall Level of Channel 1 without altering the relative settings of the Low/Mid/ High frequency Outputs. Unity gain for all Level controls is at "7". 2 Channel 2 MASTER LEVEL control: Sets the overall Level of Channel 2 without altering the relative settings of the Low/Mid/ High Outputs. 3 LOW LEVEL control: Sets the Level of signal going to the Low frequency Output only in this Channel. Refer to page Manual13 for guidance with the Level control settings. 4 LOW MUTE switch: When pressed to the in position, all signal is removed from the Low frequency Output. This eases tune-up procedures as described on pages Manual-9-14. 5 LOW DELAY control: Adds from 0 to 2 ms of time delay to the Low Frequency Output only. This allows a low frequency driver to be electronically phase-aligned with a mid frequency driver whose diaphragm is situated behind the low frequency diaphragm. Refer to pages Manual-9-12. 6 LOW / MID crossover frequency selector: This 41-detent selector sets the crossover frequency between the Low and Mid Outputs. Refer to page Manual-9. 7 MID LEVEL control: Sets the Level of signal going to the Mid Output in this Channel only. 8 MID MUTE switch: Removes all signal from the Mid Frequency Output when pressed to the in position. 9 MID DELAY control: Adds from 0 to 2 ms of time Delay to this Channel's Mid Output. 0 MID / HIGH crossover frequency selector: Sets the frequency between the Mid and High Outputs in this Channel. q HIGH LEVEL control: Sets the Level of signal going to the High Output only. w POWER indicator: Two choices: on or off. If the power is plugged in and this yellow LED is lit, then the unit ready to operate. Manual-4