Rane AC 23S Operation Manual - Page 9
Front Panel: Mono 4-way And 5-way Configuration - crossover
View all Rane AC 23S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
FRONT PANEL: MONO 4-WAY AND 5-WAY CONFIGURATION Mono 4-way and 5-way control labels are in these rows CH 1 MASTER LEVEL 46 2 8 0 10 LOW 2W: INACTIVE LEVEL 46 MUTE DELAY 46 2 8 2 8 0 10 MIN MAX LOW / MID MID 2W: INACTIVE 2W: LOW FREQUENCY 240 400 LEVEL DELAY 200 600 MUTE 150 750 4 6 46 100 850 80 900 2 8 2 8 70 1k 0 10 MIN MAX MID / HIGH 2W: LOW / HIGH FREQUENCY 700 1.0k 550 2.0k 475 2.8k 350 4.5k 250 5.8k 190 7.0k HIGH LEVEL 46 2 8 0 10 CH 2 MASTER LEVEL 46 2 8 0 10 MONO MASTER SUBWOOFER SUB / LOW MID 4W: MID / HIGH 5W: MID / HIGH-MID MONO 4W OR 5W: INACTIVE LOW 2W: INACTIVE LEVEL 46 MUTE DELAY 46 2 8 2 8 LOW / MID MID 2W: INACTIVE 2W: LOW FREQUENCY 240 400 LEVEL DELAY 200 600 MUTE 150 750 4 6 46 100 850 80 900 2 8 2 8 70 1k MID / HIGH 2W: LOW / HIGH FREQUENCY 700 1.0k 550 2.0k 475 2.8k 350 4.5k 250 5.8k 190 7.0k HIGH LEVEL 46 2 8 0 10 MIN MAX 0 10 MIN MAX 0 10 LOW LOW / MID 4W: INACTIVE 5W: HIGH-MID 4W: INACTIVE 5W: HIGH-MID / HIGH HIGH POWER AC 23S ACTIVE CROSSOVER 1 234 5 0qw e � 678 9 rty u i o Observe the labels screened below the controls for Mono operation. 1 MASTER LEVEL control: Sets the overall Level of the entire unit in Mono mode, without changing relative settings of the individual Sub/Low/Mid/High Outputs. Unity gain for all Level controls is "7". 2 SUBWOOFER LEVEL control: Sets the Level of signal going to the Sub Output. See page Manual-13. 3 SUBWOOFER MUTE switch: Removes all signal from the Sub Output when pressed to the in position. This eases the system tune-up procedure, as described on pages Manual-9-14. 4 SUBWOOFER DELAY control: In Subwoofer applications this control has virtually no effect and will normally be set to MIN (minimum). Refer to pages Manual-9-12 for alignment procedures. 5 SUB / LOW crossover frequency selector: This 41-detent selector sets the crossover frequency between the Subwoofer and Low Outputs. Refer to page Manual-9 to determine the proper setting for your system. 6 LOW LEVEL control: Sets the Level going to the Low frequency Output. 7 LOW MUTE switch: Removes all signal from the Low Output when pressed in. 8 LOW DELAY control: Adds from 0 to 2 ms of time Delay to the Low Output only. 9 LOW / MID crossover frequency selector: Sets the crossover frequency between the Low and Mid frequency Outputs. 0 MID LEVEL control: Sets the Level of signal going to the Mid Output only. q MID MUTE switch: Removes all signal from the Mid Output when pressed in. w MID DELAY control: Adds from 0 to 2 ms of time Delay to the Mid frequency Output only. e MID / HIGH‑MID crossover frequency selector: Sets the crossover frequency between the Mid and High-Mid Outputs. * NOTE: Both the CHANNEL 1 HIGH LEVEL control and CHANNEL 2 MASTER LEVEL control are automatically bypassed when the AC 23S is switched to "MONO" on the back panel. Adjusting these controls has no effect in the Mono mode. The HIGH-MID LEVEL control, HIGH-MID MUTE switch, HIGH-MID DELAY control and HIGH-MID / HIGH FREQUENCY control will have no effect regardless of their settings when the AC 23S is switched to "MONO 4-Way" on the back panel. r HlGH‑MID LEVEL control (5‑way only): Sets the Level of signal going to the High-Mid Output. t HlGH‑MID MUTE switch (5‑way only): Removes all signal from the High-Mid Output when pressed to the in position. y HlGH‑MID DELAY control (5‑way only): Adds from 0 to 2 ms of time Delay to the High-Mid Output only. u HlGH‑MID / HIGH crossover frequency selector (5‑way only): Sets the crossover Frequency between the High-Mid and High Frequency Outputs. i HIGH LEVEL control: This controls the Level of signal to the High Output only. o POWER indicator: Two choices: on or off. If the power is plugged in and this yellow LED is lit, then the unit ready to operate. Manual-6