Ridgid JP0610 Owners Manual
Ridgid JP0610 Manual
 |
View all Ridgid JP0610 manuals
Add to My Manuals
Save this manual to your list of manuals |
Ridgid JP0610 manual content summary:
- Ridgid JP0610 | Owners Manual - Page 1
OPERATOR'S MANUAL 6-1/8 in. JOINTER/PLANER JP06101 � Your Jointer/Planer has been engineered and manufactured to RIDGID's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce - Ridgid JP0610 | Owners Manual - Page 2
Needed...12 n Loose Parts...13-14 n Assembly ...14-20 n Operation ...21-28 n Adjustments...29-31 n Maintenance ...32-33 n Accessories ...34 n Troubleshooting ...34-35 n Warranty ...39 n Customer Service Information...40 INTRODUCTION This tool has many features for making its use more pleasant and - Ridgid JP0610 | Owners Manual - Page 3
injury. READ ALL INSTRUCTIONS n KNOW YOUR POWER TOOL. Read the operator's manual carefully. Learn the part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury. n USE THE RIGHT DIRECTION OF FEED. Feed work into a blade, cutter - Ridgid JP0610 | Owners Manual - Page 4
n WHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. n USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use of - Ridgid JP0610 | Owners Manual - Page 5
related support devices off the table. n AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause your hand to move into the cutter head. Never pass either hand over the cutter head during any operation. n SAVE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other - Ridgid JP0610 | Owners Manual - Page 6
operator's manual before using this product. Eye Protection Always wear safety goggles or safety glasses with side shields and a full face shield when operating this product. Safety Alert No Hands Symbol Precautions that involve your safety. Failure to keep your hands away from the blade will - Ridgid JP0610 | Owners Manual - Page 7
servicing, use only identical replacement parts. WARNING: To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator's manual. Save this operator's manual and review frequently for continuing safe operation and instructing - Ridgid JP0610 | Owners Manual - Page 8
. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Repair or replace a damaged or worn cord immediately. This tool is intended for use on a circuit that has an outlet - Ridgid JP0610 | Owners Manual - Page 9
cord plug and replace it with a 3-prong 240 volt, 15 amp. UL listed plug. n Connect the power cord white and1 3bl5ack lea2ds4,8 respectively, to the "hot" plug blade terminals. Connect the power cord green grounding wire to the plug ground prong terminal. n Plug your jointer/planer into a 220 - Ridgid JP0610 | Owners Manual - Page 10
A cutting or shaping operation made across the grain or the width of the workpiece. Cutter Head (planers and jointer planers) A rotating cutterhead with adjustable blades or knives. The blades or knives remove material from the workpiece. Dado Cut A non-through cut which produces a square-sided - Ridgid JP0610 | Owners Manual - Page 11
Per Minute 10,350/CPM OUTFEED TABLE Cutter Head 3 Knives Input 120 V, 60 Hz, AC only, 12.0 Amps Input 240 V, 60 Hz, AC only, 6.0 Amps Net Weight 208 lbs. FENCE LOCK KNOB CUTTER GUARD FENCE TILT HANDLE FENCE DEPTH INDICATOR INFEED TABLE STOP PIN FENCE STOPS � ON OFF SWITCH DEPTH OF - Ridgid JP0610 | Owners Manual - Page 12
for knife adjustment wrenches. OUTFEED TABLE The section of a jointer bed which supports the workpiece after it passes over the cutter. FENCE LOCK KNOB Allows fence to move across table front to back. This is done to achieve full width of cut or to use a different (sharper) part of cutter knives - Ridgid JP0610 | Owners Manual - Page 13
LOOSE PARTS The following items are included with your tool: 1. Motor and Switch Assembly 1 2. Jointer Bed Assembly 1 3. Motor Mount Bracket 1 4. Fence Assembly 1 5. Dust Chute 1 6. Rear Panel 1 2 7. Front Panel 1 8. Right Side Panel 1 9. Left Side Panel 1 Operator's Manual (Not shown) - Ridgid JP0610 | Owners Manual - Page 14
tool: 1. Pulley Guard 1 2. V-Belt 1 3. Angle Gauge 1 4. Cutter Guard 1 5. Push Blocks 2 6. Fence Tilt Handle 1 7. Fence Lock Knob 1 8. Handwheel 1 3 4 2 1 8 5 7 6 ASSEMBLY UNPACKING This product requires assembly. n Carefully lift jointer/planer from the carton by the base, and - Ridgid JP0610 | Owners Manual - Page 15
mount as shown using 5/16 in. carriage head bolts and 5/16 in. serrated flange nuts. Tighten the nuts with a wrench. ASSEMBLING FRONT PANEL See Figure 12. n Locate the following: Carriage Head Bolts (6), 5/16-18 x 1/2 in. Serrated Flange Hex Nuts (6), 5/16 in. Front panel with RIDGID logo (1) NOTE - Ridgid JP0610 | Owners Manual - Page 16
FEET Move the jointer/planer to the location where it will reside during use. To level the cabinet, loosen the nut and adjust leveling feet up or down as needed. Adjust all four leveling feet if necessary and then retighten the nut. NOTE: These levelers are not intended for height adjustment, only - Ridgid JP0610 | Owners Manual - Page 17
. n Place the cabinet on top of the bed assembly as shown. n Locate the following: Serrated Hex Head Bolts (3), 3/8-16 x 3/4 in. n Line up the holes in jointer table with the holes in the cabinet. n Bolt the jointer table to the cabinet using hex head bolts and tighten all the bolts. To access third - Ridgid JP0610 | Owners Manual - Page 18
of the cabinet as shown. Bolt in place using 5/16 in. carriage head bolts and 5/16 in. flange nuts. Make jointer table mounting bolts at this time. ASSEMBLING AND TENSIONING BELT See Figure 19. n Locate the V-belt. n Slip the V-belt over both the motor and cutter head pulleys. n While the jointer - Ridgid JP0610 | Owners Manual - Page 19
on top of the fence indicate where the cutter head opening is located in the table. FENCE ASSEMBLY NOTE: While installing fence to table, do not remove the protective cutter guard covering. n Position fence onto fence support as shown, making sure the keyway in fence assembly lines up with the - Ridgid JP0610 | Owners Manual - Page 20
beyond rear edge of cutter knives. n Pass a 1/4 in. thick piece of wood over the cutter head between the guard and the fence. The guard must return automatically to a "rest position" against the fence when free of the wood. If guard does not return quickly, adjust the guard spring, as described - Ridgid JP0610 | Owners Manual - Page 21
in line with the cutter head. n Always use clean, sharp, and properly-set knives. Never make cuts with dull knives. n Support the work properly before beginning a cut. n When making a cut, use steady, even pressure. Never force cuts. n Do not cut wet or warped lumber. n Adjust the depth of cut - Ridgid JP0610 | Owners Manual - Page 22
workpiece when advancing workpiece over cutter head. Use a hand-over-hand motion of the push blocks/push stick, being careful to maintain control over the workpiece at all times. This means that once the workpiece has been fed past the cutter head onto the outfeed table, one push stick/ push block - Ridgid JP0610 | Owners Manual - Page 23
1/8 in. per pass are not recommended. Rabbeting operations greater than 1/8 in. can be performed by pulling the stop pin out and lowering the infeed table in 1/8 in. increments. The pin automatically resets when you return to the 0 in. to 1/8 in. depth of cut range. Never cut a full 1/2 in. rabbet - Ridgid JP0610 | Owners Manual - Page 24
in any parts. WARNING: Test for workpiece stability with and without the push blocks before turning the jointer/planer on. Failure to do so could result in kickback of workpiece and could cause serious personal injury. n Support long workpieces at both infeed table and outfeed table. n Adjust the - Ridgid JP0610 | Owners Manual - Page 25
jointer will not necessarily make the face that is planed square or parallel to any other surface. Planing on a jointer Adjust fence to desired angle. Lock fence in position using fence tilt knob and fence be made. WARNING: Do not contact the cutting knives or the guard with the push blocks. Failure - Ridgid JP0610 | Owners Manual - Page 26
firmly against the outfeed table and against the head of the stop screw. Make sure that the infeed table does not interfere with the accuracy of measurement. The infeed table should be lowered to a depth of at least 1/16 in. Using the stops, check the fence for accuracy. If the fence is not square - Ridgid JP0610 | Owners Manual - Page 27
90° stop bar out of the way and move the fence until it contacts the 135° stop. n Make sure fence is tight against the stop and check the angle using the included angle gauge. n Using the angle gauge, set the fence at 135° to the outfeed table and tighten the bevel lock handle. n Loosen the jam - Ridgid JP0610 | Owners Manual - Page 28
. Because the workpiece is supported by the outfeed table during a rabbet cut, the infeed table must be lowered after each pass. SLIDING FENCE OPERATION See Figure 39. WARNING: Moving parts can injure. Turn jointer/ planer off and wait for all parts to stop, before adjusting fence. Failure to do so - Ridgid JP0610 | Owners Manual - Page 29
all three knives this same way. Knife Adjustment: n Loosen knife lock screws using the 8mm wrench, turning the wrench toward the fence. Remove all the parts and clean thoroughly with a gum and paste remover. Reinstall parts as shown, making sure the knife extends 1/16 in. past the cutter head as - Ridgid JP0610 | Owners Manual - Page 30
too high at either end, readjust knife. n If outfeed table needs adjustment, loosen wing screw table locks. Raise or lower the outfeed table as required by turning the outfeed table knob, until the outfeed table is exactly level with the knives of the cutter head at their highest point of revolution - Ridgid JP0610 | Owners Manual - Page 31
not use the tool. Replace the defective parts before the tool is put back in service. n When the adjustment is complete, reinstall the pan head screw in the bottom of the guard post. EXTENSION SLOT PAN HEAD SCREW CUTTER GUARD STOP POST � CUTTER GUARD ANGLE GAUGE Fig. 44 OUTFEED TABLE SOCKET HEAD - Ridgid JP0610 | Owners Manual - Page 32
, the cutter head, or the knives. Clean them with an appropriate solvent. Apply a thin coat of paste type wax to the tables and the fence so that the wood slides easily while feeding. This also deters rusting. Do not allow chips to accumulate on the underside of the jointer/planer. If power cord is - Ridgid JP0610 | Owners Manual - Page 33
the burr on the flat side. WARNING: The cutter knives are extremely sharp. Do not let your hand or fingers touch the cutter knives. Failure to heed this warning could result in serious personal injury. If the knives are nicked they must be replaced or reground. They can be reground several times - Ridgid JP0610 | Owners Manual - Page 34
nearest Authorized Service Center. 2. See "Troubleshooting (Motor)" section. 3. Adjust belt tension. Wood strikes outfeed table 1. Outfeed table improperly adjusted above 1. Readjust table, see "Outfeed Table Adjustment" after passing over cutter cutter knives section. head Ripples on planed - Ridgid JP0610 | Owners Manual - Page 35
TROUBLESHOOTING Problem Cause Solution Excessive noise 1. Motor 2. Pulley set screw is loose 1. Have motor checked by qualified service technician. Repair service is available at your nearest Authorized Service Center. 2. Tighten set screw. Motor fails to develop full power. NOTE: Low voltage - Ridgid JP0610 | Owners Manual - Page 36
NOTES 36 - Ridgid JP0610 | Owners Manual - Page 37
NOTES 37 - Ridgid JP0610 | Owners Manual - Page 38
NOTES 38 - Ridgid JP0610 | Owners Manual - Page 39
-539-1710 or by logging on to the RIDGID® website at www.ridgid.com. When requesting warranty service, you must present the original dated sales receipt. The authorized service center will repair any faulty workmanship, and either repair or replace any part covered under the warranty, at our option - Ridgid JP0610 | Owners Manual - Page 40
OPERATOR'S MANUAL 6-1/8 in. JOINTER/PLANER JP06101 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
 |
 |
Your Jointer/Planer has been engineered and manufactured to RIDGID’s high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator's manual before using this product.
Thank you for buying a RIDGID product.
OPERATOR'S MANUAL
6-1/8 in. JOINTER/PLANER
JP06101
SAVE THIS MANUAL FOR FUTURE REFERENCE
�