Ryobi TS1345L User Manual - Page 17

To Install / Replace The Blade, Warning, Caution

Get Ryobi TS1345L PDF manuals and user guides View all Ryobi TS1345L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

ASSEMBLY TO INSTALL / REPLACE THE BLADE See Figures 15 - 16. WARNING: A 10 in. blade is the maximum blade capacity of the saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from securing the blade on the spindle. Either of these situations could result in a serious accident and can cause serious personal injury.  Unplug the saw.  Loosen blade bolt cover screw. Rotate lower blade guard and blade bolt cover up and back to expose the blade bolt.  Depress the spindle lock button and rotate the blade bolt until the spindle locks.  Using the blade wrench provided, loosen and remove the blade bolt. NOTE: The blade bolt has left hand threads. Turn blade bolt clockwise to loosen.  Remove the outer blade washer. Do not remove the inner blade washer.  Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade. WARNING: If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.  Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 16.  Replace the outer blade washer. Double "D" flats on blade washers align with flats on spindle.  Depress spindle lock button and replace blade bolt. NOTE: The blade bolt has left hand threads. Turn blade bolt counterclockwise to tighten. CAUTION: Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard. SPINDLE LOCK BUTTON NOTE: BEFORE USE, REPLACE SCREWS AND TIGHTEN SECURELY TO PREVENT GUARD MOVEMENT OUTER BLADE WASHER BLADE BOLT BLADE BOLT COVER SCREW BLADE Fig. 15 INNER BLADE WASHER BLADE BOLT COVER OUTER BLADE WASHER WITH DOUBLE "D" FLATS LOWER BLADE GUARD TO LOOSEN BLADE BOLT TO TIGHTEN FLAT(S) ON SPINDLE INNER BLADE WASHER WITH DOUBLE "D" FLATS BLADE Fig. 16 17 − English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
17 − English
ASSEMBLY
TO INSTALL / REPLACE THE BLADE
See Figures 15 - 16.
WARNING:
A 10 in. blade is the maximum blade capacity of the saw.
Never use a blade that is too thick to allow outer blade
washer to engage with the flats on the spindle. Larger
blades will come in contact with the blade guards, while
thicker blades will prevent the blade bolt from securing
the blade on the spindle. Either of these situations
could result in a serious accident and can cause serious
personal injury.
Unplug the saw.
Loosen blade bolt cover screw. Rotate lower blade guard
and blade bolt cover up and back to expose the blade
bolt.
Depress the spindle lock button and rotate the blade bolt
until the spindle locks.
Using the blade wrench provided, loosen and remove the
blade bolt.
NOTE:
The blade bolt has left hand threads. Turn blade
bolt clockwise to loosen.
Remove the outer blade washer.
Do not
remove the inner
blade washer.
Wipe a drop of oil onto inner blade washer and outer
blade washer where they contact the blade.
WARNING:
If inner blade washer has been removed, replace it before
placing blade on spindle. Failure to do so could cause an
accident since blade will not tighten properly.
Fit saw blade inside lower blade guard and onto spindle.
The blade teeth point downward at the front of saw as
shown in figure 16.
Replace the outer blade washer. Double “D” flats on blade
washers align with flats on spindle.
Depress spindle lock button and replace blade bolt.
NOTE:
The blade bolt has left hand threads. Turn blade bolt
counterclockwise to tighten.
CAUTION:
Always install the blade with the blade teeth and the arrow
printed on the side of the blade pointing down at the front
of the saw. The direction of blade rotation is also stamped
with an arrow on the upper blade guard.
LOWER BLADE
GUARD
OUTER BLADE
WASHER
WITH DOUBLE
“D” FLATS
BLADE
BOLT
FLAT(S)
ON SPINDLE
BLADE
BOLT COVER
BLADE
BOLT COVER
SCREW
NOTE: BEFORE USE,
REPLACE SCREWS AND
TIGHTEN SECURELY
TO PREVENT GUARD
MOVEMENT
BLADE
BOLT
OUTER
BLADE
WASHER
BLADE
INNER
BLADE
WASHER
SPINDLE
LOCK BUTTON
TO
LOOSEN
TO
TIGHTEN
BLADE
INNER BLADE
WASHER WITH
DOUBLE “D”
FLATS
Fig. 15
Fig. 16