Samsung WA5471ABW/XAA User Manual (user Manual) (ver.1.0) (English) - Page 16

Your washer is grounded through the third prong of

Get Samsung WA5471ABW/XAA PDF manuals and user guides View all Samsung WA5471ABW/XAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

installing your washer 2. Check the inlet hoses to ensure a washer is inside the coupling of each fill hose. Cold Thread the inlet hoses onto the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and attach each fill hose to the water valve. Make sure the hose with Hot printed on it is attached to the HOT faucet. Tighten by hand until snug, then add two-thirds of a turn with pliers. Hot Rubber Washer For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an "nF" (no fill) error can occur. Cold printed 3. Turn on the "HOT" and "COLD" water supplies and check all the water valve and the faucet connections for leaks. Hot printed 4. Plug the power cord into a 3-Prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded receptacle. 5. Slide your washer into position. 6. Level your washer by turning the leveling legs in or out as necessary by hand. Your Washer must be level back to front and side to side. Use a carpenter's level on all four corners of your Washer to level it. It's a good idea after the first dozen washes to recheck your washer to ensure it is still level. 16_ installing your washer WA5471ABP-03050A_EN.indd Sec3:16 2011-03-04 1:51:31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
16_
installing your washer
2.
Check the inlet hoses to ensure a washer is inside the
coupling of each fill hose.
Thread the inlet hoses onto the HOT and COLD faucet
connections.
On the other end of the hose, check for one rubber washer
per hose and attach each fill hose to the water valve. Make
sure the hose with Hot printed on it is attached to the HOT
faucet. Tighten by hand until snug, then add two-thirds of a
turn with pliers.
For correct water use, connect both HOT and COLD water
valves. If either or both are not connected, an “nF” (no fill)
error can occur.
3.
Turn on the “HOT” and “COLD” water supplies and check all
the water valve and the faucet connections for leaks.
4.
Plug the power cord into a 3-Prong, well grounded 120 volt
60 Hz approved electrical outlet protected by a 15-amp fuse
or comparable circuit breaker.
Your washer is grounded through the third prong of the
power cord when plugged into a three-prong grounded
receptacle.
5.
Slide your washer into position.
6.
Level your washer by turning the leveling legs in or out as
necessary by hand.
Your Washer must be level back to front and side to side. Use a carpenter’s level on all four
corners of your Washer to level it. It’s a good idea after the first dozen washes to recheck
your washer to ensure it is still level.
installing your washer
Cold
Hot
Cold printed
Hot printed
Rubber Washer
WA5471ABP-03050A_EN.indd Sec3:16
WA5471ABP-03050A_EN.indd
Sec3:16
2011-03-04
1:51:31
2011-03-04
1:51:31