Samsung WA54R7600AC/US User Manual - Page 27

STEP 5, Power on, Run a test cycle

Get Samsung WA54R7600AC/US PDF manuals and user guides View all Samsung WA54R7600AC/US manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installation STEP 5 Power on Plug the power cord into an AC 120 V / 60 Hz / 15 AMP approved electrical outlet protected by a 15-amp fuse or circuit breaker. Then, press Power to turn on the washer. STEP 6 Run a test cycle Run a test cycle as follows to check if your washer is properly installed. 1. Load about 6 lb. of laundry into the tub. 2. Press Power to turn on your washer. 3. Turn the Cycle Selector to RINSE+SPIN. 4. Press and hold Start/Pause (Hold to Start) to start the test cycle. 5. The washer should not rock or vibrate excessively when water is supplied or when washing and spinning, and should drain well during the spin cycle. NOTE • If water leaks while water is being supplied or drained, check the water connections. See "Connect the water hose" on page 19. • If the washer rocks and vibrates excessively, level your washer again. See "Level the washer" on page 23. English 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
English
27
Installation
STEP 5
Power on
Plug the power cord into an AC 120 V / 60 Hz / 15 AMP approved electrical outlet
protected by a 15-amp fuse or circuit breaker. Then, press
Power
to turn on the washer.
STEP 6
Run a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1.
Load about 6 lb. of laundry into the tub.
2.
Press
Power
to turn on your washer.
3.
Turn the
Cycle Selector
to
RINSE+SPIN
.
4.
Press and hold
Start/Pause (Hold to Start)
to start the test cycle.
5.
The washer should not rock or vibrate excessively when water is supplied or when
washing and spinning, and should drain well during the spin cycle.
NOTE
•
If water leaks while water is being supplied or drained, check the water connections.
See “
Connect the water hose
” on page
19
.
•
If the washer rocks and vibrates excessively, level your washer again. See “
Level the
washer
” on page
23
.