Sanyo PDG-DXL2000 RS232C Expand - Page 22

PC Adjust Control Command, CF_FSYNC Command, CF_TDOTS Command, CF_CLAMP Command

Get Sanyo PDG-DXL2000 - 2000 Lumens PDF manuals and user guides
UPC - 086483079436
View all Sanyo PDG-DXL2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

PDG-DXL2000 Expand Serial Command Functional Specifications 8.5 PC Adjust Control Command 8.5.1 CF_FSYNC Command Command "CF_FSYNC_%1"[CR] "0000~0031 Directly select Fine Sync setting value %1 "UP Current Fine Sync setting value + 1 "DN Current Fine Sync setting value - 1 Details Set Fine Sync value of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Standby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status. Acceptable "000"[CR] Response Unacceptable "Error Code"[CR] 8.5.2 CF_TDOTS Command Command "CF_TDOTS_%1"[CR] "mmmm~nnnn" --- Directly select Total Dots setting value "mmmm" shows minimum value, it is current Display Dots value + %1 Horizontal Position value. "nnnn" shows maximum value, which is not over 150MHz. "UP Current Total Dots setting value + 1 "DN Current Total Dots setting value - 1 Details Set Total Dots of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Standby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status. Acceptable "000"[CR] Response Unacceptable "Error Code"[CR] 8.5.3 CF_CLAMP Command Command "CF_CLAMP_%1"[CR] "mmmm~nnnn" ---- Directly select Clamp setting value "mmmm" shows minimum value, fixed-value "0001". %1 "nnnn" shows maximum value: it depends on input signal. "UP Current Clamp setting value + 1 "DN Current Clamp setting value - 1 Details Set Clamp value of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Standby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status. Acceptable "000"[CR] Response Unacceptable "Error Code"[CR] 21/72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
PDG-DXL2000
Expand Serial Command Functional Specifications
21/72
8.5
PC Adjust Control Command
8.5.1
CF_FSYNC Command
Command
“CF_FSYNC_%1”[CR]
%1
“0000~0031” --------------- Directly select Fine Sync setting value
“UP” -------------------------- Current Fine Sync setting value + 1
“DN” -------------------------- Current Fine Sync setting value - 1
Details
Set Fine Sync value of PC signal
The value set by this command will not be saved to projector. Therefore, when
turning into Standby status or ALL is OFF, the value returns to original setting.
This command is available in normal Power ON status.
Acceptable
“000”[CR]
Response
Unacceptable
“Error Code”[CR]
8.5.2
CF_TDOTS Command
Command
“CF_TDOTS_%1”[CR]
%1
“mmmm~nnnn” --- Directly select Total Dots setting value
“mmmm” shows minimum value, it is current Display Dots value +
Horizontal Position value
.
“nnnn” shows maximum value, which is not over 150MHz.
“UP” -------------- Current Total Dots setting value + 1
“DN” -------------- Current Total Dots setting value - 1
Details
Set Total Dots of PC signal
The value set by this command will not be saved to projector. Therefore, when
turning into Standby status or ALL is OFF, the value returns to original setting.
This command is available in normal Power ON status.
Acceptable
“000”[CR]
Response
Unacceptable
“Error Code”[CR]
8.5.3
CF_CLAMP Command
Command
“CF_CLAMP_%1”[CR]
%1
“mmmm~nnnn” ---- Directly select Clamp setting value
“mmmm” shows minimum value, fixed-value “0001”.
“nnnn” shows maximum value: it depends on input signal.
“UP” ------------------ Current Clamp setting value + 1
“DN” ------------------ Current Clamp setting value – 1
Details
Set Clamp value of PC signal
The value set by this command will not be saved to projector. Therefore, when
turning into Standby status or ALL is OFF, the value returns to original setting.
This command is available in normal Power ON status.
Acceptable
“000”[CR]
Response
Unacceptable
“Error Code”[CR]