Sanyo PLC-XP100L Owners Manual - Page 15

Remote Control Battery Installation, Remote Control Receivers and Operating Range - replacement

Get Sanyo PLC-XP100L - XGA LCD Projector PDF manuals and user guides
UPC - 086483068263
View all Sanyo PLC-XP100L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Part Names and Functions Remote Control Battery Installation 1 Open the battery compartment lid. 2 Install new batteries into the compartment. 3 Replace the compartment lid. Press the lid downward and slide it. Two AAA size batteries For correct polarity (+ and -), be sure battery terminals are in contact with pins in the compartment. To insure safe operation, please observe the following precautions : ● Use two (2) AAA or LR03 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control to moisture or heat. ● Do not drop the remote control. ● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries. ● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Receivers and Operating Range 16.4' Point the remote control toward the projector (to (5 m) Infrared Remote Receivers) when pressing the buttons. Maximum operating range for the remote control is about 16.4' (5 m) and 60 degrees in front and rear of the projector. Infrared Remote Receivers are provided both in front and back of the projector. You can conveniently use both of the receivers (pp. 10, 51). 16.4' (5 m) Wired Remote Control Transmitter The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside of the operating range (16.4'/ 5 m). Connect the remote control and the projector with the remote control cable (sold separately). Connected with the remote control cable, the remote control does not emit wireless signal. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
15
Remote Control Battery Installation
1
2
3
Open the battery
compartment lid.
Install new batteries into
the compartment.
Replace the
compartment lid.
Press the lid downward and
slide it.
Two AAA size batteries
For correct polarity (+ and –),
be sure battery terminals are
in contact with pins in the
compartment.
To insure safe operation, please observe the following precautions :
●
Use two (2) AAA or LR03 type alkaline batteries.
●
Always replace batteries in sets.
●
Do not use a new battery with a used battery.
●
Avoid contact with water or liquid.
●
Do not expose the remote control to moisture or heat.
●
Do not drop the remote control.
●
If the battery has leaked on the remote control, carefully wipe
the case clean and install new batteries.
●
Risk of an explosion if battery is replaced by an incorrect type.
●
Dispose of used batteries according to the instructions.
Point the remote control toward the projector (to
Infrared Remote Receivers) when pressing the buttons.
Maximum operating range for the remote control is
about 16.4’ (5 m) and 60 degrees in front and rear of the
projector.
Infrared Remote Receivers are provided both in front and
back of the projector. You can conveniently use both of
the receivers (pp. 10, 51).
16.4’
(5 m)
Remote Control Receivers and Operating Range
The remote control can be used as a wired remote control. Wired
remote control helps you use the remote control outside of the
operating range (16.4’/ 5 m). Connect the remote control and
the projector with the remote control cable (sold separately).
Connected with the remote control cable, the remote control does
not emit wireless signal.
Wired Remote Control Transmitter
Part Names and Functions
16.4’
(5 m)