Sanyo PLC XU115 Instruction Manual, PLC-XU115 Network Set Up - Page 26

Connecting to the LAN line, Network environment settings, Setting Procedure - lamp for

Get Sanyo PLC XU115 - XGA LCD Projector PDF manuals and user guides
UPC - 086483071393
View all Sanyo PLC XU115 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Chapter 4 Wired LAN configurations Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately. Connecting to the LAN line Connect the LAN cable to the LAN connection terminal of the projector. LAN Connection Terminal LINK/ACT Lamp (Orange) Light or blink orange when the projector is connected to the network. LAN Cable Speed Lamp (Green) Light according to the speed of the connected network. SD 10 Base-T.........Off 100 Base-T......On * When the LAN setting is "Off", the two lamps will not be on. Network environment settings Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to "6. Basic setting and operation" (p43-62). First, complete the settings described in this chapter before performing steps in "6. Basic setting and operation." Setting Procedure 1. Turn on the projector and select "Wired" from the input menu of the projector. The projector's LINK/ACT Lamp will be on or blink. If the "Wired setting" is "Off", it will not be on. Follow step 2 and 3 to blink the lamp. 2. Select "Wired Setting" in the projector menu, and press SELECT button. Select similar LAN environment among LAN1, 2 and 3 with the Point 7 8 buttons. (LAN1, 2, and 3 are the factory default setting environments. You can select three different environment among setting LAN1-3. For each setting, refer to the chart on page 31.) When selecting "Off" in the "Wired setting", the LAN connection will be cut off. Use the function when disconnecting the projector from the network. 3. Press the Point 7 8 buttons then the "Please wait..." message will appear and switching operation will start. Switching will take a while and after completing the operation, the "Ready for use" message will appear. During the switching period, the projector cannot be operated. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
26
Chapter 4 Wired LAN configurations
SD
Setting Procedure
Setting procedures and contents differ depending on the LAN installation location.
When installing, consult your system administrator to set up the LAN appropriately.
Connect the LAN cable to the LAN connection terminal of the projector.
Network environment settings
Set the Wired LAN network through the projector menu.
Detailed network settings will be made with browser. Refer to “6. Basic setting and operation” (p43-62).
First, complete the settings described in this chapter before performing steps in “6. Basic setting and
operation.”
1. Turn on the projector and select “Wired” from the input menu of the projector.
The projector’s LINK/ACT Lamp will be on or blink. If the “Wired setting” is “Off”, it will not be on.
Follow step 2 and 3 to blink the lamp.
2. Select “Wired Setting” in the projector menu, and press
SELECT
button.
Select similar LAN environment among LAN1, 2 and 3 with the Point
7 8
buttons. (LAN1, 2, and
3 are the factory default setting environments. You can select three different environment among
setting LAN1–3. For each setting, refer to the chart on page 31.)
When selecting “Off” in the “Wired setting”, the LAN connection will be cut off. Use the function when
disconnecting the projector from the network.
3. Press the Point
7 8
buttons then the “Please wait...” message will appear and switching operation
will start. Switching will take a while and after completing the operation, the “Ready for use” message
will appear. During the switching period, the projector cannot be operated.
Connecting to the LAN line
LAN Cable
LAN Connection
Terminal
Speed Lamp (Green)
Light according to the
speed of the connected
network.
10 Base-T
.........
Off
100 Base-T
......
On
* When the LAN setting is “Off”, the two lamps
will not be on.
LINK/ACT Lamp (Orange)
Light or blink orange when
the projector is connected
to the network.