Schwinn 250 Recumbent Bike Assembly and Owner's Manual - Page 30

Power-Up / Idle Mode, Auto Shut-Off Sleep Mode, Initial Setup

Get Schwinn 250 Recumbent Bike PDF manuals and user guides View all Schwinn 250 Recumbent Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Be sure toes and knees point directly forward to ensure maximum Pedal efficiency. Pedal straps can be left in position for subsequent workouts. Console Adjustment To adjust the Console tilt position: 1. Loosen the knob behind the Console. 2. Carefully move the Console tilt to one of the available positions. 3. Tighten the knob. Power-Up / Idle Mode The Console will enter Power-Up / Idle Mode if it is plugged into a power source, any button is pushed, or if it receives a signal from the RPM sensor as a result of pedaling the machine. Auto Shut-Off (Sleep Mode) If the Console does not receive any input in approximately 5 minutes, it will automatically shut off. The LCD display is off while in Sleep Mode. Note: The Console does not have an On/Off switch. Initial Setup During the first power-up, the Console must be setup for your preferred measurement units, the machine type, and brightness of the screen. 1. Units of Measurement: Push the Increase/Decrease buttons to change between "Miles-Lb" (Imperial English) or "Km-Kg" (metric). 2. Push START/ENTER to set. 3. Machine Type: Push the Increase/Decrease buttons to change between "BIKE" and "ELLIPTICAL". 4. Push START/ENTER to set. 5. Backlight: Push the Increase/Decrease buttons to change the screen contrast, with "1" the lowest and "5" the highest. 6. Push START/ENTER to set. The Console goes back to the Power-Up / Idle Mode screen. Note: To change these choices, consult the "Console Set-Up Mode" section. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
30
Be sure toes and knees point directly forward to ensure maximum Pedal efficiency. Pedal straps
can be left in position for subsequent workouts.
Console Adjustment
To adjust the Console tilt position:
1.
Loosen the knob behind the Console.
2.
Carefully move the Console tilt to one of the available positions.
3.
Tighten the knob.
Power-Up / Idle Mode
The Console will enter Power-Up / Idle Mode if it is plugged into a
power source, any button is pushed, or if it receives a signal from the
RPM sensor as a result of pedaling the machine.
Auto Shut-Off (Sleep Mode)
If the Console does not receive any input in approximately 5 minutes, it will automatically shut off.
The LCD display is off while in Sleep Mode.
Note:
The Console does not have an On/Off switch.
Initial Setup
During the first power-up, the Console must be setup for your preferred measurement units, the
machine type, and brightness of the screen.
1.
Units of Measurement:
Push the Increase/Decrease buttons to change between “Miles-Lb”
(Imperial English) or “Km-Kg” (metric).
2.
Push START/ENTER to set.
3.
Machine Type: Push the Increase/Decrease buttons to change between “BIKE” and
“ELLIPTICAL”.
4.
Push START/ENTER to set.
5.
Backlight: Push the Increase/Decrease buttons to change the screen contrast, with “1” the
lowest and “5” the highest.
6.
Push START/ENTER to set. The Console goes back to the Power-Up / Idle Mode screen.
Note:
To change these choices, consult the “Console Set-Up Mode” section.